1300 859 933
www.evoheat.com.au
Evo315-C Manual
Page 4
4. Safety Instructions
Ensure that all safety instructions and recommendations are always adhered to. Failure to comply with these
recommendations could void the warranty and cause injury or death.
•
Installation, repair, or relocations must only be done by a
fully qualified technician.
•
The Evo315-C must be installed to conform to all relevant
Australian Standards and Industry Codes including but
not limited to: Electrical & Electrical Safety, Plumbing &
Hot Water Storage, Heat Pump Installation & Operation
•
A circuit breaker must be installed for the unit.
•
Ensure the unit has a good power connection and
earthing to avoid the risk of electrical shocks.
•
Ensure that there are no leaks on both the plumbing and
drainage fittings.
•
The unit must not be installed near flammable gas or have
flammable aerosols sprayed in the vicinity.
•
The base that the unit is installed on must be level and
stable.
•
If the supply cord is damaged, it must be replaced by a
qualified service agent.
•
This appliance must be installed in accordance with
national wiring regulations.
•
Installation must also comply with any local, state or
federal codes at the installation site. Failure to comply can
void your warranty, damage your unit or possible cause
injury or death. Plumbing must comply with
AS/NZS3500.4
•
Before obtaining access to terminals all supply circuits
must be disconnected.
•
A P&T valve
MUST
be installed in the tank. When the
tank pressure reaches 0.85MPa or when the tank
temperature reaches 99°C, the P&T valve will open
automatically so as to reduce the pressure or temperature
decrease.
•
In the event of the unit malfunctioning, shut off the
power supply and contact your supplier or EvoHeat.
•
In order to use the unit correctly, run the unit at
environment temperature -5°C - 43°C
•
The unit contains sophisticated electronic devices, do
not use unsafe water sources such as lake or
groundwater.
•
The unit produces hot water and will also have hot
fittings, therefore should not be touched to avoid injury.
•
Do not drill any fixings or attachments into the outer
casing of the tank. Drilling into the outer casing of the
tank may damage the heating coil and
WILL VOID
WARRANTY.
•
If the unit stops and you restart the unit or turn it on
manually, the unit will not start to run again for
approximately 3 minutes. This is a protection feature to
safeguard the compressor.
•
The handle of the P&T safety valve should be tested
once every six months to remove the calcium
carbonate deposits and guarantee there is no blockage
in the device.
•
Once installation is complete, check that all
connections are secure before the power is turned on.
•
The installer is to explain to the end user how to
operate and maintain the unit in accordance with this
instruction manual.
•
Evo Industries Australia Pty Ltd will not be held
responsible for any damages or injuries caused by the
incorrect installation of this hot water system.
•
A maintenance programme must be carried out as
recommended in this manual to ensure ongoing
reliability.
To reduce the risk of excessive pressures and temperatures in this water heater, install temperature and pressure protective
equipment required by local codes and no less than a combination temperature and pressure relief valve certified by a nationally
recognized testing laboratory that maintains periodic inspection of production of listed equipment or materials, as meeting the
requirements for Relief Valves and Automatic Gas Shutoff Devices for Hot Water Supply Systems, ANSIZ21.22. This valve must be
marked with a maximum set pressure not to exceed the marked maximum working pressure of the water heater. Install the valve
into an opening provided and marked for this purpose in the water heater, and orient it or provide tubing so that any discharge from
the valve exits only within 6 inches above, or at any distance below, the structural floor, and does not contact any live electrical
part. The discharge opening must not be blocked or reduced in size under any circumstances.
Hydrogen gas is produced in a hot water system served by this heater that has not been used for a long period of time (2 weeks or
more). Hydrogen gas is extremely flammable. To reduce the risk of injury under these conditions, it is recommended that the hot
water faucet be opened for several minutes at the kitchen sink before using any electrical appliance.
The appliance is fitted with means for disconnection from the supply mains having a contact separation in all poles that provide full
disconnection under overvoltage category lll conditions, and these means must be incorporated in the fixed wiring in accordance
with the wiring rules.
Содержание Evo315-C
Страница 1: ......
