manualshive.com logo in svg

Evo Affinity 30Ge, Инструкция для владельца и по установке, Страница: 4 / 28

Поделиться
Скачать
Evo Affinity 30Ge Скачать руководство пользователя страница 4

INSTALLATION INSTRUCTIONS

A f f i n i t y   3 0 G e

Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA

Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | [email protected]

3

READ FIRST

IMPORTANT PRODUCT AND SAFETY INFORMATION

WARNING    INSTALLATION OF THIS UNIT MUST BE DONE BY A QUALIFIED PLUMBER 

AND ELECTRICIAN. INCORRECT INSTALLATION CAN CAUSE INJURY 
TO PERSONNEL AND/OR DAMAGE TO EQUIPMENT. THIS UNIT MUST BE 
INSTALLED IN ACCORDANCE WITH ALL LOCAL AND UNIFORM BUILDING/
CONSTRUCTION CODES. 

 
WARNING    DO NOT INSTALL THIS UNIT TO COMBUSTIBLE SURFACES, AND DO

NOT USE COMBUSTIBLE MATERIALS IN THE CONSTRUCTION OF ANY 
COUNTER, STAND, OR OTHER DEVICE.

WARNING  THIS UNIT IS EQUIPPED WITH A THREE-PRONG (GROUNDING) PLUG FOR 

YOUR PROTECTION AGAINST SHOCK HAZARD AND MUST BE PLUGGED 
INTO GROUNDED RECEPTACLE. DO NOT MODIFY, CUT, OR REMOVE THE 
GROUNDING PRONG FROM THIS PLUG. 

WARNING    IMMEDIATELY AFTER CONNECTING GAS SUPPLY LINE AND BEFORE 

FIRST IGNITION, CHECK ALL GAS CONNECTIONS WITH SOAPY WATER 
TO TEST FOR LEAKS.

WARNING    KEEP WATER AND ALL COOKING SPILL OVERS AWAY FROM FRONT 

CONTROL PANEL AND ALL OPEN SERVICE AREAS. NEVER HOSE UNIT, 
OR SPRAY UNIT WITH CLEANING SOLUTIONS.

CAUTION   

CAREFULLY FOLLOW ALL INSTALLATION INSTRUCTIONS AND 

CONSTRUCT ALL COUNTER SPACE, STANDS, OR OTHER SURFACES TO 
THE RECOMMENDED INSTALLATION SPECIFICATIONS AS OUTLINED IN 
THIS MANUAL.

CAUTION   

THIS UNIT IS HEAVY AND SHOULD BE INSTALLED BY TWO PEOPLE. 

USE NECESSARY BLOCKING FOR LOCATING COOK SURFACE AND 
CONNECTING TEMPERATURE SENSORS TO THE UNDERSIDE OF COOK 
SURFACE.

CAUTION   

ALWAYS KEEP ANY AND ALL FLAMMABLE LIQUIDS AND COMBUSTIBLE 

MATERIALS AWAY FROM UNIT. DO NOT STORE TOWELS OR UTENSILS, 
OR ANY OTHER ITEMS ON UNIT’S DRIP PAN.

CAUTION   

DO NOT CLEAN THE COOK SURFACE WITH GRILL BRICKS OR CLEANING 

SOLUTIONS. USE ONLY GRILL SCREENS AND GRILL PADS AND FOLLOW 
THE PRESCRIBED METHOD OF CLEANING AS OUTLINED IN THIS 
MANUAL.

NOTICE       THE SERIAL NUMBER AND MODEL INFORMATION LABEL PLATE IS 

LOCATED UNDERNEATH THE CONTROL PANEL. 

NOTICE        INSTALLATION OF ANY VENT HOODS OR FIRE EXTINGUISHER SYSTEMS 

MUST CONFORM TO THE NATIONAL, STATE, AND LOCAL BUILDING AND 
ALL APPLICABLE UNIFORM CONSTRUCTION CODES.

NOTICE        DURING THE FIRST FEW HOURS OF OPERATION IT IS NORMAL FOR OILS 

USED IN THE MANUFACTURING PROCESS TO BURN OFF AND GIVE AN 
ODOR OR PETROLEUM SMOKE.

Содержание Affinity 30Ge





























Отзывы:

Нет отзывов