manualshive.com logo in svg

Evo Affinity 30Ge, Инструкция для владельца и по установке, Страница: 23 / 28

Поделиться
Скачать
Evo Affinity 30Ge Скачать руководство пользователя страница 23

OPERATOR INSTRUCTIONS

A f f i n i t y   3 0 G e

Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA

Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | [email protected]

22

INNER

000F .

Displays temperature for Inner burner (zone) in Fahrenheit degrees 
whenever Inner control knob is selected. The Dot mark after F is 
illuminated when burner is ignited. Inner display remains illuminated 
whenever Inner burner is selected.

OUTER

000F .

Displays temperature for Outer burner (zone) in Fahrenheit degrees 
whenever Outer control knob is selected. The Dot mark after F is 
illuminated when burner is ignited. Outer display remains illuminated 
whenever Outer burner is selected.

Depressing the round switch located below the ON/OFF label switches the unit between 
power On and power Off states. Switching the unit On illuminates a green light above the ON/
OFF label indicating the unit is active. Depressing the switch a second time powers down the 
unit.

ON/OFF

Is illuminated whenever there is a temperature adjustment to the Inner or Outer burner 
control knobs. SET is the default and remains illuminated until MODE switch is pressed to 
show ACTUAL temperature.

SET

Is illuminated as a safety feature to indicate cook surface temperature is above 150°F. 

HOT SURFACE

Is illuminated to show actual temperature for both Inner and Outer zones whenever MODE 
switch is pressed.

ACTUAL

Depressing the MODE button momentarily displays the actual temperature at both Inner 
and Outer zones of the cook surface. When MODE is fi rst pressed, ACTUAL is illuminated 
to indicate the temperatures displayed are the current temperatures for Inner and Outer 
zones.

When MODE is held for 4 seconds, the temperature display units change from Fahrenheit 
(°F) to Celsius (°C).

MODE

DISPLAY PANEL

SET

HOT SUR FA CE

AC TUAL

INNER

OUTER

000F .

000F .

ON/OFF

MODE

Содержание Affinity 30Ge





























Отзывы:

Нет отзывов