Evo Affinity 30Ge Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 28

Evo Affinity 30Ge Скачать руководство пользователя страница 25

OPERATOR INSTRUCTIONS

A f f i n i t y 3 0 G e

Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA

Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | [email protected]

24

REMOVABLE SPILLOVER TRAYS

The Affi nity grill has removable spillover trays concealed behind doors on the right and left side of the front control
panel. It is very important to monitor the level of spillover in the trays, and immediately empty when they are near full

Opening Spillover Tray Doors

- To open a door, grasp the door at its bottom and swing outward.

Do not operate cook top or clean drip pan into spillover slots without waste pans installed in
spillover doors. Failure to install waste pan will result in cooking grease contamination to the
underside of door. This requires immediate cleaning.

Removable
Spillover Tray

Spillover Tray

Access Door

Spillover Slot

Insert each waste pan all the way to the
back of the left and right compartments.

Do not allow spillover liquids or debris down spillover slots when doors are open. Any liquids or
debris that may fall into this area when doors are open should be immediately wiped clean.

Do not allow the spillover trays to overfl ow, and do not allow full trays to splash over edge when
cleaning. Spillover debris and liquids can be hot and cause burns.

«
...
23
24
25
26
27
...
»

Содержание Affinity 30Ge





























Отзывы:

Нет отзывов