Evo Affinity 30Ge Скачать руководство пользователя страница 26

OPERATOR INSTRUCTIONS

A f f i n i t y   3 0 G e

Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA

Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | [email protected]

25

Regular cleaning and care for your Evo Affi nity 30Ge cooktop will keep it looking and functioning it’s best.

The cooking surface is designed to hold a fi ne layer of cooking oil creating a ‘seasoning’ on its surface.  This 
seasoning promotes a non-stick cooking surface and is easily maintained.

Caring for Evo’s cooking surface is much like maintaining cast iron cookware. When the surface requires cleaning, 
there are a few basic cleaning techniques to use.  For quick and routine cleaning between preparations, a metal 
spatula or scraper works for removing the majority of surface debris.  For tougher areas or where sugars glaze 
the cook surface, pour a small amount of warm water on the soiled surface while the grill is warm and scrape the 
debris away with a spatula. Heat the cook surface to a high temperature and allow the sticky debris to become 
brittle. Once the debris is brittle, use the spatula or scraper to remove it. Afterwards wipe the cook surface with 
vegetable oil again before cooking.  

To condition the Evo cooking surface you should use the grill cleaning kit supplied with your grill.  The grill cleaning 
kit contains a blue grill pad handle, grill cleaning screen, and grill grey polishing pad.  Use the polishing pad after 
the grill cleaning pads to achieve a smooth cooking surface for the most delicate foods and applications. 

To use a grill cleaning screen:  With a warm cook surface, place one gray polishing pad between the grill handle 
base and the grill screen, so the grill screen makes direct contact with the cooking surface.  Pour a small amount 
of vegetable oil on the cook surface and scrub the surface in a circular motion. The gray polishing pad allows 
excess oil to be absorbed and scours the cooking surface of carbonized debris.  When fi nished scrubbing, wipe 
the surface down with a paper towel or cotton terry cloth. 

The drip pan located just below the cook surface is designed to catch food debris and drippings from the cook 
surface. We recommend cleaning the drip pan after your grill has cooled to prevent the possibility of touching 
hot adjoining surfaces. The drip pan is easy to wipe out with soap and water using a kitchen sponge. For added 
convenience, two removable stainless ninth-pans are mounted inside retractable drawers at right and left side of 
the front control panel for collecting drip pan debris and spill overs. These spillover trays can be easily washed by 
hand or in a dishwasher.  Be sure to empty the spillover trays after every use, and at a minimum, whenever they 
appear half full.

All the stainless steel components on your grill can be easily polished using a stainless steel cleaner/polish.  
Stainless steel cleaner can be purchased from the Evo web site along with replacement grill cleaning and polishing 
pads. The Evo web site address is:  www.evoamerica.com.

Cooking Techniques

Stovetop Cooking and Heat Zones

You can use Evo’s cook surface similar to the burners on your kitchen stove top.  Adjust Evo’s heater elements to 
control the temperatures of the cook surface “heat zones.”  Evo’s circular grill top is divided into two distinct zones. 
The center control panel knob controls the “inner heat zone,” which is also the inner circle of the cook surface at 
approximately an 11” radius from the center of the cook surface. The outer control panel knob controls the “outer 
heat zone,” which is the outer circle of the cook surface. Because the cook surface is made of heavy steel, it takes 
approximately 10 minutes from a cold start to completely heat the surface.  With a pre-heated cook surface, if you 
adjust one of the heater elements, you will have to wait momentarily before the heat zone adjusts to temperature.  

Thank You For Cooking With Evo!

COOKING SURFACE MAINTENANCE

Содержание Affinity 30Ge





























Отзывы: