manualshive.com logo in svg

Evo Affinity 30Ge, Инструкция для владельца и по установке, Страница: 24 / 28

Поделиться
Скачать
Evo Affinity 30Ge Скачать руководство пользователя страница 24

OPERATOR INSTRUCTIONS

A f f i n i t y   3 0 G e

Evo, Inc. | 8140 SW Nimbus Ave., Bldg 5 | Beaverton, Oregon 97008 USA

Phone 503.626.1802 | Fax 503.213.5869 | www.evoamerica.com | [email protected]

23

Outer Burner
Control Knob

Inner Burner

Outer Burner

On/Off & LCD Display

TEMPERATURE CONTROL

Inner Burner and Inner Control Knob

 - The Inner Burner is a 10” diameter gas fi red burner operating 

at 

15,678 BTU’s

. This burner is controlled by the Inner or center-most control knob. Temperatures 

are adjustable from 250F° to 550F°.  Starting at the Off position, the Inner Control Knob rotates 
counterclockwise beginning at 225F° and incrementing by 25F° as follows: 250°F, 275°F, 300°F, 325°F, 
350°F, 375°F, 400°F, 425°F, 450°F, 475°F, 500°F, 525°F, 550°F (Note: There is a section of the rotation 
which is blank and does not contain temperature presets).

Outer Burner and Outer Control Knob

 - The Outer Burner is a 20” diameter gas fi red burner 

operating at

 25,015 BTU’s

. This burner is controlled by the Outer or outer-most control knob. 

Temperatures are adjustable from 250°F to 550F. Starting at the Off position, the Outer Control Knob 
rotates counterclockwise beginning at 225F° and incrementing by 25F° as follows: 250°F, 275°F, 300°F, 
325°F, 350°F, 375°F, 400°F, 425°F, 450°F, 475°F, 500°F, 525°F, 550°F (Note: There is a section of the 
rotation which is blank and does not contain temperature presets).

Either the Inner or the Outer burners may be used independently to support a wide range of cooking 
techniques. Operating only the Inner burner provides direct temperature under the center of the cooking 
surface, with indirect heat at the outside edge that is useful for holding foods. Conversely, the Outer 
burner can be used for cooking foods positioned around the outside radius of the cooktop. Finally, both 
burners can be used together for maximum surface temperature and cooking versatility.

Because the cooking surface temperatures are electronically monitored to maintain a relative Set 
Temperature, surface temperature recovery occurs quickly and provides a wide range of surface 
temperature adjustment and control.

Inner Burner

Control Knob

Содержание Affinity 30Ge





























Отзывы:

Нет отзывов