manualshive.com logo in svg

Eurotech Apollo, Руководство пользователя

Поделиться
Скачать
Eurotech Apollo Скачать руководство пользователя страница 89

 

Operating system drivers 

Issue G

 

89

 

Operating system drivers 

The APOLLO has been tested with the following operating systems: 

•

 

Microsoft Windows XP. 

•

 

Microsoft Windows XP Embedded. 

•

 

Microsoft Windows 2000. 

•

 

Microsoft Windows NT4 Workstation. 

•

 

Fedora 8. 

 

Please note: 

•

 

Eurotech provides a Windows XP Embedded development kit which can be 
booted from a compact flash card or from a USB flash drive on the APOLLO 
V2Ix board. Please contact the Eurotech sales team for further information 
(see 

Eurotech Group Worldwide Presence

, page 

144

). 

•

 

The PCI UART is currently unsupported under Windows NT4. 

•

 

Eurotech provide a Linux Fedora 8 development kit that can be booted from 
a USB flash disk. Contact Eurotech Sales for further details. 

•

 

ACPI suspend/resume is not supported under Fedora 8. 

•

 

CF boot is currently unsupported under Fedora 8, boot is via a USB device. 

 

Содержание Apollo


















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды