manualshive.com logo in svg

Eurotech Apollo, Руководство пользователя

Поделиться
Скачать
Eurotech Apollo Скачать руководство пользователя страница 69

 

PhoenixBIOS features and setup 

Issue G

 

69

 

Specifying cache memory settings 

Using the memory cache can increase speed of access to data. When the memory cache 
is enabled, recently accessed data is stored in SRAM, which is faster than regular 
memory. Before accessing data in the regular memory, the CPU checks the cache. If the 
data is not held in the cache, the CPU accesses regular memory as usual. 

To specify cache memory settings, highlight 

Cache Memory

 in the 

Advanced 

menu and 

press 

Enter

. The following screen is displayed: 

 

The details you are prompted to specify for the memory cache are explained in the 
following table: 

Field 

Explanation 

Memory Cache 

Choose to enable or disable all memory caching. 

Cache System BIOS 
area 

Choose whether to cache the system BIOS. Doing so is likely 
to improve system performance significantly. You are offered 

Write Protect 

by default. This means the system BIOS is 

cached. (The system BIOS is always write protected.) 

If you don’t want to cache the system BIOS, choose 

uncached

. Please note that system performance may 

decrease rapidly as a result. 

Содержание Apollo


















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды