Eurotech Apollo Скачать руководство пользователя страница 60

Страница: 60 / 145

APOLLO user manual

Issue G

Advanced menu

The

Advanced

menu is used to configure the advanced features available on your

system’s chipset:

The following table explains the settings you can choose:

Field

Explanation

Installed O/S

Choose the operating system that is to be used, e.g. WinXP.
ACPI configuration settings are adjusted for each selected OS to
provide optimum system performance.

Reset Configuration
Data

Used to clear the Extended System Configuration Data (ESCD)
area. Select either

Yes

(to clear the area) or

. When you select

Yes

, the BIOS reinitializes the ECSD data on the next boot.

Large Disk Access
Mode

Indicate whether the operating system you’re using is DOS or
not. You are offered

DOS

by default. Change this to

Other

if you

have an operating system other than DOS, e.g. UNIX.

If the drive configuration shown in BIOS is incorrect when you
attempt to install new software, try changing this setting.

A large disk is one with more than 1024 cylinders, 16
heads or 63 tracks per sector.

Содержание Apollo


















































































































































Результаты поиска

Содержание Apollo

Отзывы:

Бренды по названию

Популярные бренды

Eurotech Apollo, Руководство пользователя

Результаты поиска

Содержание Apollo

Отзывы:

Бренды по названию

Популярные бренды