manualshive.com logo in svg

Eurotech Apollo, Руководство пользователя

Поделиться
Скачать
Eurotech Apollo Скачать руководство пользователя страница 65

 

PhoenixBIOS features and setup 

Issue G

 

65

 

Field 

Explanation 

Wake On Ring 

Choose whether the computer is to wake from 
standby/hibernation in response to a Ring Indicator (RI) signal 
from serial port COM1. 

Serial port COM2 

Choose how this port is to be configured. The options available 
are the same as for 

Serial Port COM1

, above. 

Mode 

Set the mode for this port. This can be: 

•

 

Normal

: Standard RS232 mode. 

•

 

ASK-IR: Sharp Amplitude Shift Keying mode. 

•

 

IRDA

: IrDA 1.0 infrared communications mode. 

Base I/O Address 

Specify the I/O address to be used by serial port COM2. This can 
be 2E8, 3E8, 2F8 or 3F8. 

Interrupt 

Specify the interrupt line to be used by serial port COM2. This can 
be IRQ3 or IRQ4. 

Wake On Ring 

Choose whether the computer is to wake from 
standby/hibernation in response to a Ring Indicator (RI) signal 
from serial port COM2. 

Serial Port COM4 

This serial port is based on a PCI UART, so has no I/O address or 
interrupt line configuration options. You can, however, specify the 
interface mode for this port (see below).

 

Mode 

Set the mode for serial port COM4. You are offered 

RS232

 by 

default. You can change this, if required, to 

RS485

 or 

RS422

, 

which provide additional flow control options related to auto RTS.  

Auto RTS flow control provides a mechanism whereby the serial 
port automatically switches the RS485/422 transceiver from being 
a transmitter to a receiver once the last byte has been 
transmitted. This means the user can simply read and write to the 
device as if it were a normal serial port. 

 

 

Serial Port COM3 has no BIOS configuration options as it based on a PCI UART 
and provides only RS232 output. 

Содержание Apollo


















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды