manualshive.com logo in svg

Eurotech Apollo, Руководство пользователя

Поделиться
Скачать
Eurotech Apollo Скачать руководство пользователя страница 18

APOLLO user manual 

 

Issue G

 

18 

Connecting a CompactFlash

®

 card 

The APOLLO has a single CF+ version 2.0 Type II CompactFlash

®

 socket that supports 

both Type I and Type II CompactFlash cards. This provides support for magnetic disk 
drive data storage and I/O cards such as Ethernet, serial, fax/modem, barcode scanner, 
Bluetooth, 802.11b wireless LAN, wireless digital cell phone cards and so on.  

The CompactFlash socket is connected to the CardBus/PCMCIA controller. If a 
CompactFlash card is plugged into the socket it acts as a normal hard disk drive and is 
detected by the BIOS during the POST process. If the card has an operating system 
loaded and is correctly configured to be bootable, it can be selected as a boot device 
from the BIOS boot menu. 

The CompactFlash card can only be inserted into the socket one way. The correct 
orientation is for the top of the card (i.e. the normal printed side) to be furthest from the 
PCB.  

For further details about the CompactFlash socket, see 

CompactFlash

®

 CF+ socket

, 

page 

112

. 

Connecting a keyboard 

A PS/2 keyboard can be connected to the PS/2 MiniDIN Connector. See page 

36

 for 

more information. 

Connecting a mouse 

A PS/2 mouse can be connected to the PS/2 MiniDIN Connector. See page 

36

 for more 

information. 

Turning on your APOLLO 

By default, the APOLLO BIOS is set to enter a standby state when power is applied. This 
therefore requires the operator to turn the unit ON via a remote switch connected to the 
board. The APOLLO power button connection should be connected to a momentary ON 
push button switch; this is described in 

System control interface

 on page 

105

. 

To set the APOLLO board into a mode whereby it automatically starts when AC power is 
applied, change the 

After Power Failure

 setting in the 

Power 

screen within the BIOS 

Setup. See 

Power menu

, page 

84

, for more information. 

Содержание Apollo


















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды