Eurotech Apollo Скачать руководство пользователя страница 88

Страница: 88 / 145

APOLLO user manual

Issue G

Exit menu

The

Exit

menu provides options for saving changes, discarding changes and exiting the

PhoenixBIOS setup program:

The following options are available:

Field

Explanation

Exit Saving
Changes

Saves any changes you have made, and exits the PhoenixBIOS
setup program.

Exit Discarding
Changes

Exits the PhoenixBIOS setup program without saving any of the
changes made in the current session.

Load Setup
Defaults

Reverts to the original factory-assigned BIOS settings. These are
the most stable values for the system. Use them if the system is
performing erratically due to hardware problems.

Discard Changes

Discards any changes made in the current session. You remain in
the PhoenixBIOS setup program.

Save Changes

Saves any changes you have made so far. You remain in the
PhoenixBIOS setup program.

Содержание Apollo


















































































































































Результаты поиска

Содержание Apollo

Отзывы:

Бренды по названию

Популярные бренды

Eurotech Apollo, Руководство пользователя

Результаты поиска

Содержание Apollo

Отзывы:

Бренды по названию

Популярные бренды