manualshive.com logo in svg

Eurotech Apollo, Руководство пользователя

Поделиться
Скачать
Eurotech Apollo Скачать руководство пользователя страница 57

 

PhoenixBIOS features and setup 

Issue G

 

57

 

Field 

Explanation 

Multi-Sector 
Transfers 

Specify the number of sectors transferred per block, if required. 
You can choose 2, 4, 8 or 16 sectors. Alternatively, leave this 

Disabled

 if you don’t want to specify the number of sectors 

transferred. 

LBA Mode Control 

If you want to use LBA rather than CHS settings, set this to 

Enabled

. Otherwise, leave it 

Disabled

. 

32 Bit I/O 

Choose whether you want to enable 32bit communication 
between the CPU and the IDE card. You choose either 

Disabled

 

or 

Enabled

. 

Transfer Mode 

Choose how you want data to be transferred between the drive 
and the system. You are offered the options supported by the 
drive and platform. 

Ultra DMA Mode 

Select the Ultra DMA mode to be used when transferring data to 
and from the drive. You can choose: 

•

 

Disabled 

•

 

Mode 0

, 

1

, 

2

, 

3

, 

4

 or 

5

. 

Ultra DMA mode supports 33/66/100MB/sec transfer rate for fixed 
disk drives. 

SMART Monitoring 

This is 

Enabled

 automatically if Self Monitoring Analysis and 

Reporting Technology is available on the drive. You cannot select 
it. SMART receives information from the hard drive, and provides 
a warning if hard drive failure is imminent. 

Содержание Apollo


















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды