manualshive.com logo in svg

Eurotech Apollo, Руководство пользователя

Поделиться
Скачать
Eurotech Apollo Скачать руководство пользователя страница 102

APOLLO user manual 

 

Issue G

 

102 

Secondary network interface 

The IO Controller hub contains an Ethernet controller. An external physical layer 
component provides the media interface to support 10/100 MB/s Ethernet. The Ethernet 
controller supports: 

•

 

Wake On LAN (WOL). 

•

 

Deep power down mode. 

•

 

Network boot. 

For connector details, see page 

35

. 

The APOLLO V2Ix board has the capability to enable/disable the secondary Ethernet 
port. 

Two LEDs on each RJ-45 port provide information about its operation, as follows: 

•

 

The LED on the left (as you look at the connector) tells you about the speed the port 
is currently operating at. 

•

 

The LED on the right (as you look at the connector) tells you whether the connector 
is currently linked to the network, and indicates when activity takes place via that link, 
i.e. when data is passing through. 

The information provided by each LED is explained in the following table: 

Ethernet port 

Left LED (speed) 

Right LED (link/activity) 

10/100 

Green: 100Mb/s 
Off: 10Mb/s 

Yellow: Link connected 
Flashes: Activity is taking place 

10/100/1000 

Orange: 1000Mb/s 
Green: 100Mb/s 
Off: 10Mb/s 

Yellow: Link connected 
Flashes: Activity is taking place 

Network boot 

The Primary and Secondary Ethernet controllers both provide support for Preboot 
Execution Environment (PXE) that allows for such features as remote booting and 
loading of an operating system over a network. This support is provided using the Intel 
Boot Agent Option ROMs and is configured via the BIOS setup screens – see 

Boot 

menu

, page 

86

, for further information. 

Ethernet cables 

To provide the best immunity to external interference a shielded twisted pair cable is 
recommended for use with the APOLLO board. For Gigabit Ethernet this should be rated 
as a CAT5E or higher cable. 

Содержание Apollo


















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды