manualshive.com logo in svg

Eurotech Apollo, Руководство пользователя

Поделиться
Скачать
Eurotech Apollo Скачать руководство пользователя страница 101

 

Detailed hardware description 

Issue G

 

101

 

Dual Slot PCI riser 

A dual slot 1U height PCI riser card has been designed to interface to the APOLLO 
board. This is used to provide additional PCI slots to support up to two bus master PCI 
expansion cards.  

Ethernet controllers 

The APOLLO provides two Ethernet controllers. The table below summarizes the 
controller type and supported network speeds based on APOLLO variant used. 

APOLLO variant 

Primary Ethernet controller 

Secondary Ethernet controller 

Standard (V1Ix)

 

10/100 BaseT 

82551QM Ethernet Controller 

Gigabit (V1Ix) and 
V2Ix APOLLO

 

10/100/1000 BaseT 

82541PI Ethernet Controller 

10/100 BaseT 

ICH4 + 82562ET Ethernet 
Controller 

Primary network interface 

A primary network interface controller based on the Intel 82551QM 10/100Mb Fast 
Ethernet PCI Controller is provided. The 82551QM provides efficient scatter-gather bus 
mastering capabilities enabling the 82551QM to perform high-speed data transfers over 
the PCI bus. This capability accelerates the processing of high level commands and 
operations, which lowers CPU utilization. Its architecture enables data to flow efficiently 
from the bus interface unit to the 3KB Transmit and Receive FIFOs, providing the perfect 
balance between the wire and system bus. In addition, multiple priority queues are 
provided to prevent data underruns and overruns. For connector details, see page 

35

.  

Optional Gigabit Ethernet (APOLLO V1Ix) 

An Intel 82541PI Gigabit Ethernet controller is provided on the APOLLO Gigabit build 
variant. This replaces the 82551QM device used on the APOLLO Standard and Celeron 
M 600MHz variants. 

The 82541PI provides performance up to 1000 BaseT, with backwards compatibility with 
100BaseTX and 10BaseT Ethernet standards. 

APOLLO V2Ix Ethernet 

The APOLLO V2Ix boards are fitted with an 82541PI Gigabit Ethernet connection as 
standard; the 82541PI provides performance up to 1000 BaseT, with backwards 
compatibility with 100BaseTX and 10BaseT Ethernet standards. The APOLLO V2Ix 
board has the capability to enable/disable the primary Ethernet port. 

Содержание Apollo


















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды