EUCHNER MGBS-P-L AP Series Скачать руководство пользователя страница 7

Страница: 7 / 40

2527245-02-01/22 (translation of the original operating instructions)

Operating Instructions

Safety System MGBS-P-L.-AP…

4. Exclusion of liability and warranty

In case of failure to comply with the conditions for correct use stated above, or if the safety regulations are not followed,

or if any servicing is not performed as required, liability will be excluded and the warranty void.

5. General safety precautions

Locking modules fulfill personnel protection functions. Incorrect installation or tampering can lead to fatal injuries to personnel.
Check the safe function of the safeguard particularly

after any setup work

after the replacement of a system component

after an extended period without use

after every fault

Independent of these checks, the safe function of the safeguard should be checked at suitable intervals as part of the

maintenance schedule.

WARNING

Danger to life due to improper installation or due to bypassing (tampering). Safety components perform

a personnel protection function.

Safety components must not be bypassed, turned away, removed or otherwise rendered ineffective.

On this topic pay attention in particular to the measures for reducing the possibility of bypassing

according to EN ISO 14119:2013, section 7.

The switching operation may be triggered only by handle modules designated for this purpose.

Prevent bypassing by means of replacement handle modules (only for multicode evaluation). For this

purpose, restrict access to handle modules and to keys for releases, for example.

Mounting, electrical connection and setup only by authorized personnel possessing the following

knowledge:

-specialist knowledge in handling safety components

-knowledge about the applicable EMC regulations

-knowledge about the applicable regulations on operational safety and accident prevention.

Important!

Prior to use, read the operating instructions and keep these in a safe place. Ensure the operating

instructions are always available during mounting, setup and servicing. EUCHNER cannot provide any

warranty in relation to the readability of the CD for the storage period required. For this reason you

should archive a printed copy of the operating instructions. You can download the operating instruc-

tions from www.euchner.com.

Содержание MGBS-P-L AP Series









































Результаты поиска

Содержание MGBS-P-L AP Series

Отзывы:

EUCHNER MGBS-P-L AP Series, Руководство по эксплуатации, Страница: 7 / 40

Результаты поиска

Содержание MGBS-P-L AP Series

Отзывы: