EUCHNER MGBS-P-L AP Series Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 40

EUCHNER MGBS-P-L AP Series Скачать руководство пользователя страница 31

31

2527245-02-01/22 (translation of the original operating instructions)

Operating Instructions

Safety System MGBS-P-L.-AP…

EN

Parameter

Value

Unit

min.

typ.

max.

Monitoring outputs OL, OI, OD

p-switching, short circuit-proof

Output voltage

0.8 x UB

-

UB

V DC

Max. load

-

-

50

mA

Solenoid

Solenoid operating voltage IMP (reverse polarity protected,

regulated, residual ripple < 5%)

DC 24 V +10%/-15%

Solenoid current consumption I

IMP

400

mA

Connection rating

6

W

Duty cycle

100

%

Reliability values acc. to EN ISO 13849-1

Mission time

20

years

Monitoring of guard locking and the guard position

Category

4

Performance Level (PL)

e

PFH

D

4.1 x 10

-9

/h

Control of guard locking

Category

Depends on external control

Performance Level (PL)

PFH

D

1) Dependent on the handle module used.

2) Trip characteristic medium slow-blow.

3) Values at a switching current of 50 mA without taking into account the cable lengths.

4) Corresponds to the actuation frequency.

14.1.1. Typical system times

Please refer to the technical data for the exact values.

Ready delay

: After switch-on, the device carries out a self-test. The system is ready for operation only after this time.

Turn-on time of safety outputs

: The max. reaction time t

on

is the time from the moment when the guard is locked to the

moment when the safety outputs switch on.

Risk time according to EN 60947-5-3

: If a handle module moves outside the actuating range, the safety outputs

(FO1A and FO1B) are deactivated at the latest after the risk time.

Discrepancy time

: The safety outputs

(FO1A and FO1B) switch with a slight time offset. They have the same signal

state no later than after the discrepancy time.

Test pulses at the safety outputs

: The device generates its own test pulses on the safety outputs (FO1A and FO1B).

A downstream control system must tolerate these test pulses.
This can usually be set up in the control systems by parameter assignment. If parameter assignment is not possible for your

control system or if shorter test pulses are required, please contact our support organization.
The test pulses are also output when the safety outputs are switched off.

«
...
29
30
31
32
33
...
»

Содержание MGBS-P-L AP Series









































Отзывы:

Нет отзывов