EUCHNER MGBS-P-L AP Series Скачать руководство пользователя страница 29

Страница: 29 / 40

2527245-02-01/22 (translation of the original operating instructions)

Operating Instructions

Safety System MGBS-P-L.-AP…

13. System status table

Operating mode

Actuator/door position

Safety outputs FO1A

and FO1B

Guar

d lock monitoring

output OL

Door position monitor

ing output OD

LED indicator

Output

LOCK (yellow)

State

ATE (gr

een)

DIA (r

ed) and

diagnostic moni

toring output OI

Normal operation

closed

Normal operation, door closed and locked

closed

off

1 x in-

verse

Normal operation, door closed and not locked

open

off

1 x

Normal operation, door open

Teach-in operation

(only unicode)

open

off

3 x

Device in teach-in standby

closed

off

1 Hz

Teach-in operation

off



Positive acknowledgment after completion of teach-in opera-

tion

Fault display

off

1 x

Error in the teach-in operation (only unicode)

Actuator removed from the actuating range prior to the end of

the teach-in operation or faulty actuator detected

off

2 x

Input fault

Test pulses on the safety outputs cannot be read due to

synchronous tests pulses on UB

off

3 x

Read error

(e.g. actuator faulty)

off

4 x

Output fault

(e.g. short circuit, loss of switching ability)

off

5 x

Disabled actuator detected

off

Internal fault

Key to symbols

LED not illuminated

LED illuminated

1 x inverse

LED illuminated, briefly goes off 1 x

1 Hz

LED flashes at 1 Hz

3 x

LED flashes three times, and this is then repeated



LEDs flash alternately

Any state

After the cause has been remedied, faults can generally be reset by opening and closing the guard. If the fault is still dis-

played afterward, use the reset function or briefly interrupt the power supply. Contact the manufacturer if the fault could

not be reset after restarting.

Important!

If you do not find the displayed device status in the system status table, this indicates an internal device

fault. In this case, you should contact the manufacturer.

Содержание MGBS-P-L AP Series









































Результаты поиска

Содержание MGBS-P-L AP Series

Отзывы:

EUCHNER MGBS-P-L AP Series, Руководство по эксплуатации, Страница: 29 / 40

Результаты поиска

Содержание MGBS-P-L AP Series

Отзывы: