manualshive.com logo in svg

EtherWAN EX24000, Руководство пользователя

Поделиться
Скачать
EtherWAN EX24000 Скачать руководство пользователя страница 51

 

This is a read-only page that will allow the user to see what devices are connected to a 
particular port and the vlan associated with that device and port. 

To clear the MAC addresses for a particular port on the EX24000 Switch (see 

Figure 21

): 

1.  Click on the link to the port at the top of the Per Port VLAN Activities page. 

2.  Click on the 

Clear MAC

 button at the bottom of the page. 

3.  The statistics for the port will update every ten seconds. 

 

 

Figure 21: Port VLAN Activities 

 

 

Port Security Dynamic-MAC 

To navigate to the 

Port Security Dynamic-MAC

 page: 

1.  Click on the 

+

 next to 

Port

. 

2. Click on

 Port Security Dynamic-MAC.

 

The Port Security Dynamic-MAC submenu allows the user to control access to the ports on 
the switch based on the source MAC addresses of the network devices. You specify the 
maximum number of source MAC addresses that ports can learn. Ports that learn their 
maximum number of addresses discard packets that have new, unknown addresses, 
preventing access to the switch by any additional devices.  

51 

EX24000 Switch Users Guide 

Содержание EX24000
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды