manualshive.com logo in svg

EtherWAN EX24000, Руководство пользователя

Поделиться
Скачать
EtherWAN EX24000 Скачать руководство пользователя страница 204

 

1.  From the dropdown list next to 

VLAN ID

, choose the VLAN that you want the IGMP 

Snooping process to run on. 

2.  From the dropdown list next to 

IGMP Version

, choose the correct IGMP version to 

be run on this VLAN. This setting must match the IGMP version being used by the 
IGMP querier and the IGMP client on the network. 

3.  Choosing the appropriate choice (Enable or Disable) from the dropdown list next to 

Fast Leave

.  

  If this feature is enabled on the switch, and the switch receives a request to 

leave a multicast stream on a port, then the switch will drop this multicast 
stream on that port without checking to see if there are any other multicast 
clients on that port that might still be interested in receiving this multicast 
stream. This allows the multicast stream to disappear from a port much faster. 

1.  Next, click on the 

Update Setting

 button 

 

 

Figure 100: IGMP General Properties 

 

Configuring IGMP Passive Mode Specific properties 

To navigate to the 

IGMP Snooping 

page: 

1.  Click on the 

+

 next to 

Other Protocols

. 

2. Click on 

IGMP Snooping

. 

204 

EX24000 Switch Users Guide 

Содержание EX24000
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды