EtherWAN EX24000 Скачать руководство пользователя страница 135 | Manualshive

Страница: 135 / 239

background image

VLAN

Port Based VLAN vs. Tagged Based VLAN

The EX24000 Switch can be configured to operate in one of two VLAN modes: Port based
VLAN mode or Tagged based VLAN mode. In Port based VLAN mode, packets from
different VLANs can only be segregated from one another while within a single switch, but
not when the packets travel to other switches in the network. The VLAN association rule for
all incoming packets in Port based VLAN mode is determined only by the VLAN ID that is
associated with the port when a packet enters the switch.

In Tagged based VLAN mode, traffic from different VLANs can be segregated from one
another even after it travels to another switch. This is done by “tagging” (inserting
information inside a packet) a packet with the VLAN ID that the packet belongs to when the
packet exits the switch. The VLAN association rule for incoming packets in Tag based VLAN
mode can either be based on the VLAN ID that is assigned to the port (PVID) when a packet
enters the switch (in the event when the packet does not contain a VLAN ID), or it can be
determined from the packet itself (when the packet does contains a VLAN ID).

Configuring VLANs in Port Based VLAN Mode

Enabling Port Based VLAN

To navigate to the

VLAN Mode Setting

page:

1. Click on the

+

next to

VLAN

.

2. Click on

VLAN Mode Setting.

To enable Port Based VLAN on the switch:

1. Select Port-based VLAN from the dropdown box (see

)

2. Click on the

Submit

button.

3. Save the configuration (see the

Save Configuration Page

)

135

EX24000 Switch Users Guide

«
...
133
134
135
136
137
...
»

Содержание EX24000
















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EX24000

SmartPro DGS-1500-20

Бренд: D-Link Страницы: 113

xStack DGS-3120 Series

Бренд: D-Link Страницы: 1150

Бренд: Gefen Страницы: 31

Бренд: ORiNG Страницы: 2

TIMEGUARD WF10COM

Бренд: Theben Страницы: 35

Sierra Video 1208V3S

Бренд: Kramer Страницы: 2

Бренд: Exsys Страницы: 14

CRSMEO-4 Series

Бренд: Festo Страницы: 16

PFS4226-24ET-240

Бренд: Dahua Страницы: 3

Бренд: Manhattan Страницы: 2

Magnum CS14 Series

Бренд: GarrettCom Страницы: 76

Бренд: AbleNet Страницы: 6

Бренд: LINK-MI Страницы: 12

Бренд: Kathrein Страницы: 41

IMI Sensors 691A80

Бренд: PCB Piezotronics Страницы: 15

Бренд: PCB Piezotronics Страницы: 31

Бренд: Nortel Страницы: 46

Бренд: Kramer Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды