EtherWAN EX24000 Скачать руководство пользователя страница 194 | Manualshive

Страница: 194 / 239

background image

General Overview

To enable the GVRP protocol on your network, you must make sure that the switches in
your network are configured with the minimum requirements for each type of switches listed
below:

For the

Access Switches

at the edge of the network, below are the minimum requirements:



All of the user VLANs have been created in the VLAN Database.



The IP address for the Management VLAN has been configured.



The appropriate Port Type (Access or Trunk) and the PVID have been configured for

all the ports of the switch.



All the member Trunk ports for all the user VLANs have been configured.



The GVRP protocol has been globally enabled, and GVRP is locally enabled on the

Trunk Ports as well.

For the

Distribution Switches

in the core of the network, below are the minimum

requirements:



The Management VLAN has been created in the VLAN Database.



The IP address for the Management VLAN has been configured.



The appropriate Port Type (Access or Trunk) and the PVID have been configured for

all the ports of the switch.



The GVRP protocol has been globally enabled and GVRP is locally enabled on the

Trunk Ports as well.



The Dynamic VLAN Creation feature has been enabled.

194

EX24000 Switch Users Guide

«
...
192
193
194
195
196
...
»

Содержание EX24000
















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для EX24000

Бренд: Magnetrol Страницы: 12

Бренд: Magnetrol Страницы: 24

Бренд: D-Link Страницы: 357

Бренд: 3Com Страницы: 8

PathBuilder S200 Series

Бренд: 3Com Страницы: 11

Бренд: 3Com Страницы: 8

CoreBuilder 3500

Бренд: 3Com Страницы: 96

Бренд: 6TL Страницы: 25

Бренд: FS Страницы: 33

Бренд: Eaton Страницы: 43

Бренд: Hamlet Страницы: 4

IPES-5222T Series

Бренд: Lantech Страницы: 30

Бренд: Alloy Страницы: 33

Бренд: Cable Electronics Страницы: 16

USB 2.0 7-Port Hub HO97916

Бренд: GE Страницы: 19

Бренд: 3Com Страницы: 74

Бренд: Lindy Страницы: 54

Бренд: Opengear Страницы: 109

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды