EtherWAN EX24000 Скачать руководство пользователя страница 202

Страница: 202 / 239

IGMP Snooping

The settings in the IGMP Snooping feature of the EtherWAN switch controls how the switch
forwards multicast packets.

General Overview

The EX24000 Switch has been outfitted with the IGMP Snooping function in three modes:



Disabled:

The switch will forward all multicast packets according to the

Forced

Forwarding Port

setting based on the following rule:



All multicast packets will be forwarded to only the port specified by

either the

PassiveForwardMode

or the

ForcedForwardMode

function.



Passive mode:

The switch will forward any multicast packets that have known receivers to

the known multicast receiver ports only.

The switch will forward any unknown multicast packets (multicast packets

without any known receivers) according to the

Forced Forwarding Port

setting based on the following rule:



When there is no Querier Port (a port that receives IGMP queries)

present all unknown multicast packets will be forwarded to the port
specified by either the

PassiveForwardMode

function or the

ForcedForwardMode

function.



When there is a Querier port present, the switch will forward all

unknown multicast packets to the Querier port. In addition, all
unknown multicast packets will be forwarded to the port specified by
the

ForcedForwardMode

function as well.



Querier mode:

The switch will forward any multicast packets that have known receivers to

the known multicast receiver ports only.

The switch will forward any unknown multicast packets according to the

Forced Forwarding Port

setting based on the following rule:



All unknown multicast packets will be sent to only the port specified by

the

ForcedForwardMode

function.

202

EX24000 Switch Users Guide

Содержание EX24000
















































































































































































































































Результаты поиска

Содержание EX24000

Отзывы:

Похожие инструкции для EX24000

Бренды по названию

Популярные бренды

EtherWAN EX24000, Руководство пользователя

Результаты поиска

Содержание EX24000

Отзывы:

Похожие инструкции для EX24000

Бренды по названию

Популярные бренды