manualshive.com logo in svg

EtherWAN EX24000, Руководство пользователя

Поделиться
Скачать
EtherWAN EX24000 Скачать руководство пользователя страница 207

 

With IGMP enabled, the EtherWAN switch will transmit all multicast packets to their only 
multicast receiver ports. However, some multicast packets will not have any known multicast 
receiver ports either due to IGMP Snooping being disabled on the switch, or because no 
multicast receiver has sent IGMP requests for these multicast packets. The multicast 
packets in these scenarios are referred to as 

unknown multicast packets

. You can use the 

Passive Mode Forwarding Port

 section of the IGMP Snooping configuration page to 

control how the switch will forward these unknown multicast packets under different IGMP 
Snooping modes of the switch (see 

Figure 103

). 

 

Disabled Mode Forwarding Port Configuration 

When IGMP is in Disabled Mode, all multicast packets are unknown multicast packets, and 
by default all unknown multicast packets are forwarded to all the ports of the switch. To 
modify the default behavior and to control how the switch will forward unknown multicast 
packets when the switch is in 

IGMP Snooping Disabled mode

: 

1.  Select either the 

PassiveForwardMode

 or the 

ForceForwardMode

 radio button.  

2.  Make sure that only the ports that you would like to have the 

unknown multicast 

packets

 to be forwarded to, have a check mark next to it.  

3.  Then click on the 

Update Setting

 button. 

 

 

Figure 103: Disabled Mode Forwarding Port 

 

Passive Mode Forwarding Port Configuration  

207 

EX24000 Switch Users Guide 

Содержание EX24000
















































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды