Espa Evopool SilenPlus ControlSystem Скачать руководство пользователя страница 10

Страница: 10 / 32

If you do not have

ControlSystem

or prefer not to use it,

the system can work just as well manually.
Ignore the activation and calibration operations, switch
to Manual mode and then connect the

4.5 Changing the

ControlSystem

If it is necessary to replace the

ControlSystem

system that is already linked, you will need to delete
the old serial number before linking the new one.
To do this, with the

SilenPlus

pump connected to the

power supply, keep the

button pressed down for 10

seconds.  Flashing  LEDs  indicate  that  the  operation
has been carried out correctly.
The  previous  serial  number  will  be  deleted
system  will  go  into  “link  standby”  mode.  Proceed  as
indicated in 4.2.2.

5. OPERATION
5.1

REMOTE

mode

This is the default operating mode.
The pump carries out the most appropriate function
considering the position of the filter valve. (See figure
3)
In FILTRATION position:

Filtration Plus

•

In BACKWASH position:

Backwash

•

In CLOSED position: pump stopped.

•

In any of the other positions: the pump operates at

100% power.

•

When you operate the valve control, the pump

stops automatically to make the valve movement
easier.

•

In any intermediate position, the pump remains

stopped.

To change the working mode, simply move the valve
to the desired position.

To  prevent  accidental  operation,  the  electronic
response is delayed by  1 second. The
red  LED  indicates  that  proper  communication
has been achieved.
Move the valve gently.

WARNING: the valve configuration must correspond
to the 6 standard positions, according to figure 3.
For other valve configurations, contact your technical
service.

5.2

MANUAL

mode

When you press the

, key

SilenPlus

ignores the

trolSystem

signal and runs one of the preset functions:

The MAN LED comes on.
The pump starts up  at  a fixed, programmable speed.
The  standard  setting  is  2,300  RPM  (40  Hz).  This  is
what is known as the MIXED CYCLE (MISC. CYCLE).
If  you  press  the

key, it runs through the various

SilenPlus

functions in sequence.

or prefer not to use it,

the system can work just as well manually.

ctivation and calibration operations, switch

to Manual mode and then connect the

SilenPlus

ControlSystem

in a

system that is already linked, you will need to delete

fore linking the new one.

pump connected to the

button pressed down for 10

seconds. Flashing LEDs indicate that the operation

The previous serial number will be deleted and the
system will go into “link standby” mode. Proceed as

The pump carries out the most appropriate function
considering the position of the filter valve. (See figure

Filtration Plus

function

Backwash Plus

function

In CLOSED position: pump stopped.
In any of the other positions: the pump operates at

When you operate the valve control, the pump

ally to make the valve movement

In any intermediate position, the pump remains

To change the working mode, simply move the valve

To  prevent  accidental  operation,  the  electronic
response is delayed by  1 second. The flashing
red  LED  indicates  that  proper  communication

WARNING: the valve configuration must correspond
to the 6 standard positions, according to figure 3.
For other valve configurations, contact your technical

ignores the

Con-

signal and runs one of the preset functions:

The pump starts up at a fixed, programmable speed.
The standard setting is 2,300 RPM (40 Hz). This is

is known as the MIXED CYCLE (MISC. CYCLE).

key, it runs through the various

Between each function, the pump stops to allow valve
movement or other operations.
The sequence is:

1. Mixed cycle (MISC. CYCLE).
2. Stop.
3.

Filtration Plus

4. Stop.

Backwash Plus

6. Stop.
7. Mixed cycle...

The lit LEDs indicates the function selected at all
times.
When you press the

button again, you leave Ma

ual mode to go back to Remote.

5.3 No water fault and retries.

Filtration Plus

mode, the system is regularly mon

tored to check that the pump is not operating without
water.
If

SilenPlus

detects the pump is working without water

it stops the motor.
The  system  will  attempt  to  start  up  again  after  1',  5',
15'  and  1  hour  (Fig.  4).  If  th
remain in permanent fault mode.
An LED sequence indicates the fault status. (See fi
ure 7)
To  interrupt  the  retry  cycle  or  to  restart  from  perm
nent fault mode, press the

5.4 System status

Espa offers installers and us
plication for monitoring the system status and
interacting with

SilenPlus

You need to have an Android device with Blu
tooth connectivity and
available from

www.espa.com

With this app, it is possible to switch between

ual/Remote

modes and use all functions.

6. ADVANCED CONFIGURATION

Different speeds can be set to adjust the functions to
the characteristics of the installation.
The function being run will be configured.
To configure a function, first select it, either in Manual
or Remote mode, and at the same time press
for 5 seconds.
All the speeds of the selected function will return to
the factory settings [= fs]
To increase or decrease the speed, press M or F:

M = + 58 RPM (+ 1 Hz)
F = - 58 RPM (- 1 Hz)

•

Configuring

Filtration Plus

The filtration speed is set.
· Minimum = 1,600 RPM (20 Hz), [= fs]
· Maximum = 2,900 RPM (50 Hz), [= fs]

Between each function, the pump stops to allow valve
movement or other operations.

Mixed cycle (MISC. CYCLE).

The lit LEDs indicates the function selected at all

button again, you leave Man-

ual mode to go back to Remote.

5.3 No water fault and retries.

mode, the system is regularly moni-