Epson RX595 - Stylus Photo Color Inkjet Скачать руководство пользователя страница 86

Страница: 86 / 131

EPSON Stylus Photo RX585/RX595/RX610

Revision B

Disassembly and Assembly

Disassembly and Assembly of Major Parts of Printer

Lubrication is necessary. Refer to the following section and
lubricate the specified points:

LUBRICATION OF ASF ASSY

(p.121)

LUBRICATION OF LD ROLLER SHAFT

(p.120)

When installing the ASF Assy, make sure that the composite
gear, the chip of Change Lever and the hooks (x2) are engaged
properly.

Tighten the screws in the specified order.

(Fig. 4-64)

Install the LD Roller aligning the arrow on the LD Roller with
the arrow on the blade of the shaft. Make sure the LD Roller is
securely attached without any gap or misalignment.

ASF Unit

Align the arrows

Blade

LD Roller Shaft

LD Roller

LD Roller Shaft

Содержание RX595 - Stylus Photo Color Inkjet




































































































































Результаты поиска

Содержание RX595 - Stylus Photo Color Inkjet

Отзывы:

Epson RX595 - Stylus Photo Color Inkjet, Руководство по обслуживанию, Страница: 86 / 131

Результаты поиска

Содержание RX595 - Stylus Photo Color Inkjet

Отзывы: