manualshive.com logo in svg

Epson RX595 - Stylus Photo Color Inkjet, Руководство по обслуживанию, Страница: 41 / 131

Поделиться
Скачать
Epson RX595 - Stylus Photo Color Inkjet Скачать руководство пользователя страница 41

EPSON Stylus Photo RX585/RX595/RX610

Revision B

Troubleshooting

Troubleshooting When There is Error Display

41

3.2  Troubleshooting When There is Error Display

3.2.1  Error List

C H E C K

P O I N T

The messages displayed on the LCD that are listed in the “Error 
List” above and “

Warning List 

(p.42)

” on the next page and 

subsequent pages are given only for information. In other words, 
they are not exactly the same as the messages actually displayed.

Table 3-1.  Error List 

Error Name

Displayed Message

Occurrence Condition

Recovery Procedure

Maintenance Error

Waste ink pad in the printer is saturated. Contact your dealer 
to replace it.

The printer requires maintenance due to waste liquid 
overflow or elastomer tube replacement time, etc.

Replace the waste ink pads.

See “6.1.1 Maintenance Error” 

(p.116)

Printer FATAL Error

A printer error has occurred. Please see your manual.

An irrecoverable error has occurred.

Turn off the power

See “3.2.3 FATAL Error” 

(p.46)

Paper jam

It is likely that a paper jam has occurred in the printer. Turn 
off the printer, then open the scanner unit and remove the 
paper. See your documentation.

A paper jam in a printer and a printer mechanism cannot 
operate normally.

The power is turned off and a paper is 
removed from a printer mechanism part.

Scanner Error

A scanner error has occurred. Please see your manual.

The error that was not able to be recovered with the 
scanner occurred.

Turn off the power

See “6.1.1 Maintenance Error” 

(p.116)

Message related to Ink (1)

Cannot recognize ink cartridges. Make sure the ink cartridges 
are installed correctly.

The ink cartridges have not been inserted or defective ink 
cartridges have been inserted.

Install the normal ink cartridges correctly 
and press the OK button.

Message related to Ink (2)

Ink cartridge cover is open. Open the scanner unit and close 
the ink cartridge cover.

Ink cartridges were replaced with new ones with the ink 
cartridge fixation cover open.

Close the ink cartridge fixation cover and 
press the OK button

Paper Detect Error

Paper jam. Load paper and press Start. If the error does not 
clear, repeat the procedure.

A sheet was loaded in a wrong orientation and caused a 
jam.

Follow the displayed message until the 
sheet loaded in a wrong orientation is 
ejected.

Paper Jam Error

Paper or CD/DVD jam or feed error. Press Start. If the error 
does not clear, remove the media by hand.

The paper jam has occurred.

Turn power off, and remove the paper.

Message related to Ink (3)

Cannot recognize ink cartridges.

The ink cartridge had not been inserted at an initial filling 
or the ink cartridge error occurred

Install the normal ink cartridges filled with 
ink correctly and press the OK button.

Message related to Ink (4)

Press the OK button to replace ink cartridges.

Ink end

Install the normal ink cartridges filled with 
ink correctly and press the OK button.

Содержание RX595 - Stylus Photo Color Inkjet




































































































































Отзывы:

Нет отзывов