Epson RX595 - Stylus Photo Color Inkjet Скачать руководство пользователя страница 70

Страница: 70 / 131

EPSON Stylus Photo RX585/RX595/RX610

Revision B

Disassembly and Assembly

Removal of Exterior Parts

4.2.5 Middle Housing Assy

Remove the Panel Assy (p.63)

Remove the Scanner Unit (p.65)

Remove the Main Board Assy / Case Open Sensor (p.66)

Remove the Waste Ink Tray Assy (p.69)

5. Remove the screw and remove the Hinge Assy (left and right).

6. Remove the screws (3 in the front and 2 in the rear) securing the Middle Housing

Assy.

7. Remove the Middle Housing Assy with care not to get any cable caught.

(Continued to next page)

Figure 4-25. Removing the Hinge Assy

Figure 4-26. Removing the Middle Housing Assy

C A U T I O N

After removing the Waste Ink Assy, take due care not to stain any
surrounding objects with waste ink.

Hinge Assy B (Long): Left side

Hinge Assy B (Short): Right side

C.B.P-TITE 3x10 (x2)

Torque : 0.6±0.1N

C.B.P-TITE 3x10 (x5)

Torque : 0.6±0.1N

Содержание RX595 - Stylus Photo Color Inkjet




































































































































Результаты поиска

Содержание RX595 - Stylus Photo Color Inkjet

Отзывы:

Epson RX595 - Stylus Photo Color Inkjet, Руководство по обслуживанию, Страница: 70 / 131

Результаты поиска

Содержание RX595 - Stylus Photo Color Inkjet

Отзывы: