Epson RX595 - Stylus Photo Color Inkjet Скачать руководство пользователя страница 9

EPSON Stylus Photo RX585/RX595/RX610

Revision B

Product Description

Features

9

1.1  Features

EPSON Stylus Photo RX585/RX595/RX610 are color inkjet printers equipped with 
scanner function. The main features are described below.

†

Available Functions

„

Printer

• Printing from a PC
• Direct print on CD or DVD (label print)

„

Scanner

• Scanning from a PC
• Scan to Memory function

(directly stores a scan data to a memory card inserted)

„

Stand-alone copy

• Stand-alone copy using the printer and scanner functions.

„

Memory card slot

• Direct print from a memory card
• Accessible from a PC as a USB memory card slot

„

USB host interface

• Direct print from an external USB storage device
• Direct backup of memory card data to an external USB storage device
• Direct print from a digital camera (PictBridge/USB Direct Print)

„

2.5-inch TFD color LCD

†

High speed & high quality

„

Maximum resolution: SMGA 5760 (H) x 1440 (V) dpi

„

High speed print with a newly developed F3 Mach Turbo2 head
(Black: 90 nozzles x 1 column, Color: 90 nozzles x 5 columns/color)

„

High quality with 6 colors dye ink (6 independent cartridges)

„

Borderless print on EPSON designated paper

†

Dimensions

„

Dimensions: 450 mm (W) x 413 mm (D) x 205 mm (H)

(when the ASF and the stacker are closed. includes the rubber feet)

„

Weight:

8.3 kg 

 (excludes the ink cartridges and the power supply cable)

Figure 1-1.  External View

Содержание RX595 - Stylus Photo Color Inkjet




































































































































Отзывы: