manualshive.com logo in svg

Epson RX595 - Stylus Photo Color Inkjet, Руководство по обслуживанию, Страница: 38 / 131

Поделиться
Скачать
Epson RX595 - Stylus Photo Color Inkjet Скачать руководство пользователя страница 38

EPSON Stylus Photo RX585/RX595/RX610

Revision B

Operating Principles

Banding Reduction System (BRS)/ Paper Feed Profile Correction (PFP)

38

2.3  Banding Reduction System (BRS)/ Paper Feed Profile Correction (PFP)

†

Overview

To ensure high-speed printing and high print quality, this printer is provided with the Banding Reduction System (BRS) and Paper Feed Profile Correction (PFP) function, which are 
outlined below:

†

How to prepare correction data

For each of BRS and PFP, print the relevant pattern for correction data preparation and read the printed pattern through the scanner. Then calculate the correction data and store the data 
in the serial flash ROM on the Main Board. The correction data are applied to printing in the supported printing mode.

Table 2-6. Outline of Banding Reduction System and Paper Feed Profile Correction Function

Outline

Supported Printing Mode

Remarks

Paper Type

Paper 

Size

Printing 

Resolution 

(dpi)

EAI

Other than EAI

BRS

Conventional models perform overlapping printing (two-pass or four-
pass printing) to reduce banding for ensuring high print quality. 
However, the printer provided with the Banding Reduction System 
corrects the dot generation rate (amount of settled ink) for each raster, 
and performs one-pass printing. This function ensures both high print 
quality (reduction of banding) and high-speed printing.

Ultra Premium Photo Paper Glossy

Premium Photo Paper Glossy

Photo Paper Glossy

Premium Photo Paper Semi-Gloss

Ultra Glossy Photo Paper

Premium Glossy Photo Paper 

Glossy Photo Paper

Premium Semigloss Photo Paper

4x6

720x720

–

PFP

The conventional paper feed adjustment method is such that the 
correction value calculated from the data based on a specific part of the 
sheet is reflected to almost all over the sheet. Therefore, the 
conventional method cannot cope with the fluctuating error in the paper 
feed rate during paper feeding. However, the Paper Feed Profile 
Correction function measures the error in the paper feed rate at each of 
minutely distributed measuring points on the sheet and provides a 
correction value for each point. Thus with this function, the printer 
realizes high print quality and high-speed printing on a supported paper 
type and in a supported printing resolution.

Ultra Premium Photo Paper Glossy

Premium Photo Paper Glossy

Photo Paper Glossy

Premium Photo Paper Semi-Gloss

Ultra Glossy Photo Paper

Premium Glossy Photo Paper 

Glossy Photo Paper

Premium Semigloss Photo Paper

4x6

720x720

With BRS

720x360

Without BRS

C H E C K

P O I N T

Refer to 

Chapter 5 “Adjustment”

 for details of correction data 

preparation for BRS and PFP.

Содержание RX595 - Stylus Photo Color Inkjet




































































































































Отзывы:

Нет отзывов