Epson RX595 - Stylus Photo Color Inkjet Скачать руководство пользователя страница 67

Страница: 67 / 131

EPSON Stylus Photo RX585/RX595/RX610

Revision B

Disassembly and Assembly

Removal of Exterior Parts

INSTALLATION PROCEDURE FOR THE MAIN BOARD ASSY

1. Check the Middle Housing for the following conditions.

(Fig. 4-17)

The Card Slot Cover can be opened and closed properly.

The IRDA sheet has been installed properly.

2. Install the Main Board Assy on the Middle Housing.

(See p.66)

3. Separate the cables and FFCs into three groups, A, B and C.

(Fig. 4-18)

(Continued to next page)

Figure 4-17. Checking the Middle Housing

Figure 4-18. Separating the cables and FFCs

Figure 4-19. Connectors on the Main Board

Tighten the screws in the order specified to secure the Main Board
and Main Board Assy. (

Fig. 4-16

)

Group

CN No.

Color

Connected to

Remarks

CN14

White CR Motor

2-pin

CN13

Black PF Motor

2-pin

CN6

White PE Sensor

3-pin

CN7

Black APG Sensor

3-pin

CN8

(FFC) PF Encoder

5-pin

CN4

White CD-R Sensor (Guide & Tray)

4-pin

CN3

White Power Supply Board

3-pin

CN10

(FFC) Printhead

13-pin

CN11

13-pin

CN12

9-pin

CN15

(FFC)

CSIC Board

13-pin

CN16

PW Sensor

6-pin

CN17

White CR Motor (Scanner Unit)

2-pin (With ferrite core)

CN19

(FFC) CIS Unit

14-pin (With ferrite core)

CN20

White Scanner Encoder

4-pin

–

CN22

(FFC) Panel Board

8-pin

–

CN23

(FFC) LCD Module

11-pin

C H E C K

P O I N T

See the figure at right

(Fig. 4-19)

for the connector layout of the

Main Board.

For the connector assignment of the Scanner Unit,

see

“4.2.2 Scanner Unit”

(p.65)

OPEN

CLOSED

Card Slot Cover

Torsion spring

IRDA sheet

Group B

Group A

Group C

(FFCs)

CN4

CN3

CN14

CN6

CN8

CN13

CN23

CN22

CN10

CN11

CN12

CN15

CN16

CN20 CN17

CN19

CN7

Содержание RX595 - Stylus Photo Color Inkjet




































































































































Результаты поиска

Содержание RX595 - Stylus Photo Color Inkjet

Отзывы:

Epson RX595 - Stylus Photo Color Inkjet, Руководство по обслуживанию, Страница: 67 / 131

Результаты поиска

Содержание RX595 - Stylus Photo Color Inkjet

Отзывы: