Epson RX595 - Stylus Photo Color Inkjet Скачать руководство пользователя страница 121

Страница: 121 / 131

EPSON Stylus Photo RX585/RX595/RX610

Maintenance

121

LUBRICATION OF ASF ASSY

Described below are the lubrication points of the ASF Assy for the case where the LD Roller Shaft is locked and those for the case where the Hopper has been released.

When LD Roller Shaft is locked

When Hopper has been released

Lubrication Points LD Roller Assy

Type

G-71

Amount of
Application

Left side of the LD Roller Shaft:

ø1x5 mm

Vicinity of the LD Roller:

On the rib (x4)

Right side of the LD Roller Shaft: ø1x5 (x2)

ø1x10

Applying Tool

Injector

Precautions

When LD Roller Shaft is locked

Left side of LD Roller

Shaft

1x5 mm

Vicinity of LD Roller

Right side of LD Roller Shaft

1x10 mm

1x5 mm (x2)

Lubrication Points LD Roller Assy

Type

G-71

Amount of
Application

Left side of the LD Roller Shaft: ø1x20 mm
Vicinity of the LD Roller:

On the rib (x4)

Right side of the LD Roller Shaft: ø1x10 (x2)

Applying Tool

Injector

Precautions

When Hopper has been released

Left side of LD

Roller Shaft

1x20 mm

Vicinity of LD

Roller

Right side of LD

Roller Shaft

1x10 mm (x2)

Содержание RX595 - Stylus Photo Color Inkjet




































































































































Результаты поиска

Содержание RX595 - Stylus Photo Color Inkjet

Отзывы:

Epson RX595 - Stylus Photo Color Inkjet, Руководство по обслуживанию, Страница: 121 / 131

Результаты поиска

Содержание RX595 - Stylus Photo Color Inkjet

Отзывы: