Epson R800 - Stylus Photo Color Inkjet Printer страница 42 Скачать руководство пользователя

Страница: 42 / 76

EPSON Stylus Photo R800

Revision A

TROUBLESHOOTING

Overview

Table 3-4. Phenomenon-Based Paper Out Error Check Points

Occurrence

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

At operation

When the Paper Switch was
pressed, the LD Roller
attempt to feed paper but the
paper is not fed.

ASF Assy.

1. Check the LD Roller or Retard Roller of the ASF Assy. for

paper dust and foreign matter.

1. Using a cleaning sheet, clean the LD

Roller and Retard Roller. The procedure
is as follows.

(1)

Place the cleaning sheet upside
down and put it into the ASF Assy.

(2)

Press the Paper Switch to start
paper feed.

(3)

Repeat the above steps several
times.

* To remove persistent contamination,

staple an alcohol-dampened cloth to a
postcard and clean the rollers in the
following method.

(1)

Place the alcohol-dampened cloth
toward the LD Roller surface of the
ASF Assy.

(2)

Hold the mount top end securely
and press the Paper Switch.

(3)

Repeat the paper feed sequence
several times to clean the LD Roller
surface of the ASF Assy.

Cleaning sheet

Postcard used

as mount

Non-adhesive part

Adhesive part

This side down

Stapling

Cloth damped

with alcohol

Download Service Manual And Resetter Printer at http://printer1.blogspot.com

Содержание R800 - Stylus Photo Color Inkjet Printer













































































Результаты поиска

Содержание R800 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R800 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды

Epson R800 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию

Результаты поиска

Содержание R800 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R800 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды