Epson R800 - Stylus Photo Color Inkjet Printer страница 66 Скачать руководство пользователя

Страница: 66 / 76

EPSON Stylus Photo R800

Revision A

TROUBLESHOOTING

Overview

Ink stain of paper

Ink stain occurs at the back
or end of the print paper.

Front Paper

Guide Pad

1. Check that heaps of ink are not formed on the Front Paper

Guide Pad and that the Front Paper Guide Pad is installed
securely and evenly in the setting position.

1. If heaps of ink are formed, replace the

Front Paper Guide. If it has been
confirmed that the Ink pads have risen,
reinstall the Front Paper Guide Pad
correctly.

When the paper size in the
sent print data is larger than
the size of the fed paper, data
are printed on the Front
Paper Guide, extending off
the paper.

PW Sensor

1. Check that the PW Sensor FFC is connected.

1. Connect the PW Sensor FFC.

2. Check that the PW Sensor is not faulty.

2. Change the PW Sensor for a new one.

Ink sticks to other than the
print area of the paper,
resulting in contamination.

Paper EJ Frame

Assy.

1. Check the Star Wheel Rollers for ink stain.

1. Clean the Star Wheel Rollers with a soft

cloth.

Front Paper

Guide

1. Check the Front Paper Guide for ink stain.

1. Clean the Front Paper Guide with a soft

cloth.

Front Paper

Guide Pad

1. Check that ink heaps are formed on the Front Paper Guide

Pad.

1. Change the Front Paper Guide for a new

one.

Table 3-15. Print Quality Fault Check Points

Print Quality State

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

Front Paper Guide Pad

Front Paper Guide

Download Service Manual And Resetter Printer at http://printer1.blogspot.com

Содержание R800 - Stylus Photo Color Inkjet Printer













































































Результаты поиска

Содержание R800 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R800 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды

Epson R800 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию

Результаты поиска

Содержание R800 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R800 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды