Epson R800 - Stylus Photo Color Inkjet Printer страница 65 Скачать руководство пользователя

Страница: 65 / 76

EPSON Stylus Photo R800

Revision A

TROUBLESHOOTING

Overview

White streak/color

unevenness

occurrence

(Continued)

White streaks/color
unevenness occurs
horizontally in a fixed cycle
during 360dpi printing.

Adjustment

1. Check that PF Adjustment is executed properly.

1. Perform PF Adjustment properly. (Refer

to Chapter 5

"ADJUSTMENT"

2. Check for Dot missing.

2. Change the Ink System Unit for a new

one.

Star Wheel Rollers traces
appear relative to the CR
moving direction.

Paper EJ Frame

Assy.

1. Check that the Star Wheel Units have not come off or the

Star Wheel Rollers turn.

1. Install the Star Wheel Units to the Paper

EJ Frame Assy. correctly.

Printing is executed but blur
occurs.

Printer Driver

and Exclusive

Paper

1. Check that adequate paper is used according to the setting

of the Printer Driver.

1. Use adequate paper according to the

setting of the Printer Driver.

Print Head

1. Using the Adjustment Program, check that the correct Head

ID has been written to the EEPROM.

1. Using the Adjustment Program, enter the

31- digit code of the Head ID to the
EEPROM.
(Refer to Chapter 5

"ADJUSTMENT"

Occurrence of

Paper EJ Roller

traces

Paper EJ Roller traces occur
during printing of print paper
or CD-R.

Printer Driver

and Exclusive

Paper

1. Check that adequate paper is used according to the setting

of the Printer Driver.

1. Use adequate paper according to the

setting of the Printer Driver.

Table 3-15. Print Quality Fault Check Points

Print Quality State

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

Star Wheel Roller

Star Wheel Units

Download Service Manual And Resetter Printer at http://printer1.blogspot.com

Содержание R800 - Stylus Photo Color Inkjet Printer













































































Результаты поиска

Содержание R800 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R800 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды

Epson R800 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию

Результаты поиска

Содержание R800 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R800 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды