Epson R800 - Stylus Photo Color Inkjet Printer страница 53 Скачать руководство пользователя

Страница: 53 / 76

EPSON Stylus Photo R800

Revision A

TROUBLESHOOTING

Overview

Table 3-12. Phenomenon-Based Cutter Position Error Check Points

Occurrence

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

At Cutter unit fitting

(At power-on)

At power-on, an error is
displayed on the Paper LED
and EPW3.

Cutter Motor

1. Check that the Connector cable of the Cutter Motor is

connected to the Relay Board Connector (CN2).
(When the Cutter position is other than the HP)

1. Connect the Connector cable of the Cutter

Motor to the Relay Board Connector.

2. Check the Cutter Motor or Connector cable for damage.

(When the Cutter position is other than the HP)

2. Change the Cutter Motor for a new one.

The Cutter produces
operating noise.

Cutter HP

Sensor (right)

1. Check the Cutter HP Sensor (right) or the rail groove of the

Cutter for paper dust, foreign matter, etc.

1. Remove the paper dust, foreign matter,

etc. from the Cutter HP Sensor (right) or
the rail groove of the Cutter.

2. Check that the Connector cable of the Cutter HP Sensor

(right) is connected to the Cuter HP Sensor (right) and
Relay Board Connector (CN4).

2. Connect the Connector cable of the Cutter

HP Sensor (right) to the Cuter HP Sensor
(right) and Relay Board Connector.

3. Check the Cutter HP Sensor (right) for damage.

3. Change the Cutter HP Sensor (right) for a

new one.

CN2

Cutter Motor

Cutter HP Sensor (right)

CN4

Download Service Manual And Resetter Printer at http://printer1.blogspot.com

Содержание R800 - Stylus Photo Color Inkjet Printer













































































Результаты поиска

Содержание R800 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R800 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды

Epson R800 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию

Результаты поиска

Содержание R800 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R800 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды