Epson R800 - Stylus Photo Color Inkjet Printer страница 25 Скачать руководство пользователя

Страница: 25 / 76

EPSON Stylus Photo R800

Revision A

OPERATING PRINCIPLES

Printer Mechanism

2.2.5 Ink System Mechanism

The Ink System Mechanism consists of the following mechanisms.

Pump Unit (including the CR Lock Lever)

Cap Unit

2.2.5.1 Pump Unit

The Pump Unit is designed to suck ink from the Print Head or Cap Unit. The
Cap Unit has a built-in Head Cleaning Wiper.

The following indicates the Pump Unit driving stepping motor specifications.

The following operations are performed when the drive of the Pump Motor is
transmitted to the Pump Unit.

Note: As the rotation directions of the motor, CW indicates a clockwise

direction, and CCW indicates a counterclockwise direction, as seen
from the output shaft side of the motor mounting plate.

2.2.5.2 Drive Transmission Path to Pump Unit

The drive of the Pump Motor is transmitted to the Pump Unit in the following
path.

Motor Pinion Gear

⇒

Combination Gear 10.2, 21.2 IS

⇒

Spur Gear 20.4 IS

⇒

Pump Unit

The following shows the internal part names and operation outline of the Pump
Unit.

Figure 2-9. Outline of Pump Unit Inside

Table 2-7. Pump Motor Specifications

Item

Specifications

Type

4-phase, 48-pole PM type stepping motor

Drive voltage

Bipolar drive/constant-current drive

Winding resistance

+42V ± 5% (voltage applied to driver)

Inductance

10.3

Ω

± 10% (per phase at 25°C)

Drive method

13.4mH ± 20% (1kH, 1Vrms)

Table 2-8. Pump Motor Rotation Directions and Functions

Pump Motor Rotation Direction*

Functions

CW direction

• Cap closing

• Ink suction

• Wiper resetting

• CR Lock setting

CCW direction

• Cap opening

• Pump release

• Wiper setting

• CR Lock resetting

Motor Pinion Gear

Pump Unit inside

Combination Gear 10.2, 21.2 IS

Spur Gear

20.4 IS

Download Service Manual And Resetter Printer at http://printer1.blogspot.com

Содержание R800 - Stylus Photo Color Inkjet Printer













































































Результаты поиска

Содержание R800 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R800 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды

Epson R800 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию

Результаты поиска

Содержание R800 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R800 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды