Epson R800 - Stylus Photo Color Inkjet Printer страница 20 Скачать руководство пользователя | Manualshive

Страница: 20 / 76

background image

EPSON Stylus Photo R800

Revision A

OPERATING PRINCIPLES

Printer Mechanism

21

2.2.3.1 ASF Paper Feeding Mechanism

The following indicates the ASF Assy. driving stepping motor specifications.

The drive of the ASF Motor is transmitted to the LD Roller in the following path.

LD Roller Drive Transmission Path
ASF Motor Pinion Gear

⇒

Combination Gear 29, 11

⇒

Paper Back Cam

⇒

LD Roller

Figure 2-5. LD Roller Drive Transmission Path

Driven by the ASF Motor, the ASF Assy. performs the following feeding
operation.

1.

When a paper feeding command is issued from the PC or the Paper Switch
of the panel is pressed after power-on, the driving force of the ASF Motor
begins to be transmitted to the LD Roller.

2.

The flag of the Paper Back Cam moves away from the home position of the
ASF Sensor and the LD Roller rotates.

3.

When the LD Roller rotates one turn and the flag of the Paper Back Cam
returns to the home position of the ASF Sensor again, the LD Roller stops
rotating.

2.2.3.2 Manual Paper Feeding Mechanism (Board Paper)

To enable direct printing onto thick paper and CD-R label, this product has the
mechanism to feed paper from the printer front manually.

1.

When the Stacker is lifted, the close signal of the PG Release Sensor is
transmitted to the APG Assy. in the following order.

PG Release Sensor

⇒

Main Board

⇒

Relay Board

⇒

APG Motor

⇒

APG Assy.

2.

Driven by the APG Motor, the APG Assy. sets the PG position to PG
release to release the Upper Paper Guide (Driven Roller).

3.

Along the Paper Feed Guide of the Stacker, match the leading edge (front
side) of the board paper to the marking position of the Stacker.

After the above operation, press the Paper Switch. When the PE Sensor
detects that the paper is present, it detects the leading edge of the paper, and
the printer performs paper locating and then enters the standby status.

Table 2-5. ASF Motor Specifications

Item

Specifications

Type

4-phase, 48-pole PM type stepping motor

Drive voltage

Bipolar drive/constant-current drive

Winding resistance

+42V ± 5% (voltage applied to driver)

Inductance

7.4

Ω

± 10% (per phase at 25°C)

Drive method

12.0mH ± 20% (1kH, 1Vrms)

ASF Motor

LD Roller Shaft

Paper Back Cam

Combination Gear 29, 11

Download Service Manual And Resetter Printer at http://printer1.blogspot.com

«
...
18
19
20
21
22
...
»

Содержание R800 - Stylus Photo Color Inkjet Printer













































































Отзывы:

Нет отзывов

Похожие инструкции для R800 - Stylus Photo Color Inkjet Printer

Бренд: Canon Страницы: 12

imagePROGRAF iPF8300S

Бренд: Canon Страницы: 52

Бренд: Canon Страницы: 2

Бренд: FEIYUTECH Страницы: 8

Бренд: FeiYu Tech Страницы: 2

Бренд: FeiYu Tech Страницы: 2

Бренд: FEIYUTECH Страницы: 26

Бренд: Parker Страницы: 2

Бренд: Park Tool Страницы: 2

Бренд: ParaZero Страницы: 17

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренд: Öhlins Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды