Epson R800 - Stylus Photo Color Inkjet Printer страница 38 Скачать руководство пользователя

Страница: 38 / 76

EPSON Stylus Photo R800

Revision A

TROUBLESHOOTING

Overview

Table 3-2. Phenomenon-Based Communication Error Check Points

Occurrence

Timing

Phenomenon Detail

Faulty Part/

Part Name

Check Point

Remedy

At power-on

The printer does not operate
at all.

Panel FFC

1. Check that the Panel FFC is securely connected to the

Panel Board connector and Main Board connector (CN8).

1. Connect the Panel FFC to the Panel

Board and Main Board connectors.

2. Check the Panel FFC for damage.

2. Change the Panel FFC for a new one.

Panel Board

1. Check the Panel Board for damage.

1. Change the Panel Board for a new one.

Power Supply

Board

1. Check that the Connector cable of the Power Supply

Board is securely connected to the Main Board (CN7).

1. Connect the Connector cable of the

Power Supply Board.

2. Check that the blue line side pin of the Power Supply

Board Connector cable is inserted into the 1 Pin. (Refer to
the above photo.)

2. Match and connect the blue line of the

Power Supply Board Connector cable
into the 1 Pin.

Panel Board

connector

Panel FFC

Main Board

connector

Connector cable

of the Power

Supply Board

Blue line

1Pin side

Download Service Manual And Resetter Printer at http://printer1.blogspot.com

Содержание R800 - Stylus Photo Color Inkjet Printer













































































Результаты поиска

Содержание R800 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R800 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды

Epson R800 - Stylus Photo Color Inkjet Printer, Руководство по обслуживанию

Результаты поиска

Содержание R800 - Stylus Photo Color Inkjet Printer

Отзывы:

Похожие инструкции для R800 - Stylus Photo Color Inkjet Printer

Бренды по названию

Популярные бренды