Epson R800 - Stylus Photo Color Inkjet Printer страница 24 Скачать руководство пользователя | Manualshive

Страница: 24 / 76

background image

EPSON Stylus Photo R800

Revision A

OPERATING PRINCIPLES

Printer Mechanism

25

The fed paper is detected by the PE Sensor, and its leading edge is then
transferred to the front of the Front Paper Guide.
To eliminate the deflection of the paper, the paper is then returned toward the
ASF Assy. by the specified number of steps according to the paper feed mode.
The paper is transferred again to the specified paper locating position of the
Front Paper Guide.

Figure 2-8. Paper Loading Mechanism 2

2.2.4.2 PF Measurement Sequence

The mechanical load in the paper loading path is measured in the following
cases to perform control so that an adequate current value is set according
to the mechanical load.

When power is switched on

When the Ink Cartridge is replaced

When the removal or fitting of the cutter is recognized in the paper feed
sequence

When the mechanical load in the paper loading path reaches the specified
value, Fatal Error is displayed. (When the cutter is not fitted)

When the cutter is fitted, the mechanical load when the cutter is fitted is
measured and reflected on the control since the mechanical load of the
cutter must be taken into consideration to set the adequate current value.

Paper

Star Wheel Rollers

Print Head

Driven Roller

PF Roller

Paper eject roller (front)

Paper eject roller (rear)

Download Service Manual And Resetter Printer at http://printer1.blogspot.com

«
...
22
23
24
25
26
...
»

Содержание R800 - Stylus Photo Color Inkjet Printer













































































Отзывы:

Нет отзывов

Похожие инструкции для R800 - Stylus Photo Color Inkjet Printer

AUTOSTROKE AST-200-V2

Бренд: StoneAge Страницы: 28

Бренд: EBS Страницы: 4

Бренд: NCR Страницы: 38

Бренд: Ranger design Страницы: 6

Бренд: UnderCover Страницы: 16

Бренд: Safco Страницы: 6

Бренд: Oki Страницы: 210

Бренд: Panasonic Страницы: 77

Бренд: Unitech Страницы: 2

Бренд: Acdeos Страницы: 38

Бренд: A&D Страницы: 35

Бренд: FujiFilm Страницы: 13

Бренд: Scame electrical solutions Страницы: 8

Бренд: Fisher-Price Страницы: 8

Бренд: Whispbar Страницы: 15

Бренд: Graphite Страницы: 44

Бренд: BCS Страницы: 151

Бренд: Home Accents Holiday Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды