Epson EU-T532 Скачать руководство пользователя страница 61

Страница: 61 / 118

5-6

Repair

Rev. A

Confidential

Paper is not
fed.

Paper is not fed
smoothly.

(1)The paper roll

supply module
does not
oscillate
properly.

Check if the paper is
pulled out smoothly.
(The paper tension
loading should be less
than the rating value.)

•

Load the paper

properly.

•

Replace the paper

roll supply module if
  the oscillation
  loading of the
  paper supply
  module is
  excessive.

(2) The paper size is
not

correct.

Check the paper
diameter, width, and
thickness.

Use the specified
paper.

Paper is not fed.

(1)Abnormal input

signal or paper
feed motor
failure

Check the power
supply voltage, input
signal, and operation
of each paper feed
motor.

•

Replace the
control circuit
board module if
there is any
problem with the
power supply
voltage, input
signal.

•

Replace the motor
if there is any
problem with the
motor operation.

(2)The paper feed

connector is
disconnected.

Check if the each
paper feed motor is
connected properly.

Connect the
connector properly.

(3)Power

transmission parts
(gears) are
damaged, or
foreign matter is
caught between
gears.

•

Check the power

transmission state of
each gears.

•

Check if no foreign

matter is caught
between geas.

•

Replace damaged

gears.

•

Remove foreign

matter if there is
any.

Table 5-1 Troubleshooting

Phenomenon

Condition

Cause

Level

Where/how to check

Procedure

Содержание EU-T532























































































































Результаты поиска

Содержание EU-T532

Отзывы:

Похожие инструкции для EU-T532

Бренды по названию

Популярные бренды

Epson EU-T532, Техническое руководство

Результаты поиска

Содержание EU-T532

Отзывы:

Похожие инструкции для EU-T532

Бренды по названию

Популярные бренды