Epson EU-T532 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 118

background image

Rev. A

Operation Principles 2-11

EU-T532/T542 Technical Manual

Confidential

Black marks are detected through changes in output level from the reflective photo sensor. The
changes in reflectivity between the pre-printed black marks and blank areas of the thermal
paper cause the amount of light returning to the sensor to vary; then the sensor output level is
also varied as shown in Figure 2-15. These variations are used to detect the black mark. Since the
relationship between the black mark and the print position can be specified in the printer set up,
detecting the black mark permits the correct positioning of the paper.

Figure 2-15 Black mark detecting operation

Autocutter Mechanism

This mechanism consists of the fixed blade mechanism, the movable cutter blade mechanism
and the emergency cutter mechanism.
The basic principle of the autocutter mechanism is an application of the scissors principle, where
the paper is cut by two crossing blades. A configuration which allows the two blades to separate
has been adopted so that the

fixed blade, H

separates from the

movable cutter blade, full, H

when the

platen

is open.

Fixed blade mechanism

This mechanism is mounted on the frame platen unit. This configuration consists of the

fixed

blade, H

which cuts the paper directly, the

spring, fixed blade

which stabilizes the vertical

positioning of the

fixed blade, H

, and the

cover, fixed blade

which covers the

fixed blade,

H

and is a paper guide as well as makes the operation to open the

platen

safe.

Figure 2-16 Fixed blade mechanism

black mark detector signal

conductive confirmation

black mark detection

spring, fixed blade

fixed blade, H

cover, fixed blade

frame, platen unit

«
...
20
21
22
23
24
...
»

Содержание EU-T532























































































































Отзывы:

Нет отзывов

Похожие инструкции для EU-T532

Бренд: Oki Страницы: 8

Бренд: Oki Страницы: 48

Stylus Pro 7900

Бренд: X-Rite Страницы: 36

Бренд: Dascom Страницы: 12

Бренд: Dascom Страницы: 19

Бренд: Dascom Страницы: 5

Бренд: Panduit Страницы: 74

Бренд: Tally Страницы: 2

Бренд: Tally Dascom Страницы: 57

Бренд: Fenix Страницы: 65

Бренд: Nantian Electronics Страницы: 4

Бренд: OKIDATA Страницы: 182

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 143

Бренд: oti Страницы: 33

Бренд: Planmeca Страницы: 56

Бренд: Ricoh Страницы: 269

Бренд: Creality Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды