Epson EU-T532 Скачать руководство пользователя страница 60

Страница: 60 / 118

Rev. A

Repair 5-5

EU-T532/T542 Technical Manual

Confidential

Printing is faint.

All printing color is
faint.

Printing density
setting is set to light.
(The color sensitivity
difference
depending on the
paper)

•

Check the printing

density setting of the
control circuit module.

•

Check if the specified

paper is used.

Change the setting
of the printing
density to darken.

All or some part
of printing is faint.

(1)Dirt or foreign

matter attaches
to the head
heating
elements.

See or check the head
heating elements with
a magnifier.

Clean the head
heating elements if
foreign matter is
attached to the
elements.

(2)Thermal

sensitivity has
deteriorated
due to paper
deterioration

Check whether the
paper has
deteriorated.

Replace the
deteriorated paper.

(3)Thermal head
heating

elements are
defective.

Check the surface of
the thermal head with
a magnifier.

Replace the thermal
head.

Printing is partly
faint.

Damage or
deformation of the
platen surface

See or check with a
magnifier the platen
surface.

Replace the platen
if the platen surface
is damaged or
deformed.

Abnormal or
incorrect
printing

Abnormal or
incorrect printing

(1)Thermal head
input pulse
failure

Check with an oscillo-
scope if the input pulse
is within the specified
range.

If the input pulse is
abnormal, replace
the control circuit
board.

(2)Thermal head

failure
(Dr.IC, etc.)

If input pulse is
normal, replace the
thermal head.

Paper cannot
be inserted.

Paper cannot be
inserted into the
printer module.

(1)Paper chips or

foreign matter is
in the paper
guide of the
printer module.

Check whether paper
chips or foreign matter
is inside the paper
guide.

Remove paper
chips or foreign
matter if there is
any.

(2)Paper detector

on the paper
guide of the
printer module is
defective.

Check if the detector
operates properly.

•

Remove paper

  chip or foreign
  matter if there is
  any.

•

Replace the

detector if it is
damaged.

(3)The shape of the

paper edge is
not like the

specified one.

Check if the paper
edge is cut properly.

Cut the paper edge
properly.

Table 5-1 Troubleshooting

Phenomenon

Condition

Cause

Level

Where/how to check

Procedure

Содержание EU-T532























































































































Результаты поиска

Содержание EU-T532

Отзывы:

Похожие инструкции для EU-T532

Бренды по названию

Популярные бренды

Epson EU-T532, Техническое руководство

Результаты поиска

Содержание EU-T532

Отзывы:

Похожие инструкции для EU-T532

Бренды по названию

Популярные бренды