Epson EU-T532 Скачать руководство пользователя страница 42

Страница: 42 / 118

Rev. A

Handling 3-7

EU-T532/T542 Technical Manual

Confidential

Loading paper for printer module

Follow the steps below to load the paper for the printer module from the paper roll supply
module.

1. Cut the edge of the paper as shown in Figure 3-4.

Figure 3-4 Shape of paper edge

2. Pull out the paper and pass it under the

roller, paper roll tension

3. After inserting the paper edge straight into the paper slot of the printer module so that the

paper is along the upper side of the

plate, lower paper guide

, push the paper with your

hand.

4. When the inserted paper is detected by the

paper-end detector

of the printer module, the

paper is fed automatically in the semi-autoloading mode.

5. When the semi-autoloading is finished, the extra paper is automatically cut.

6. Remove the extra paper from the

paper exit

Note:

•

Performing operations other than above can cause improper paper feeding and jamming.

•

Make sure that the paper is not wrinkled or torn.

•

To avoid paper jams, do not fold the edge of the paper.

•

Paper curled in the opposite direction from the paper entrance might be difficult to insert.

•

If the paper is not inserted at a right angle, paper jams or paper folding may occur. In this case,
open the

platen unit

, and load the paper properly after removing a paper jam.

•

Do not apply excessive pressure to the

shaft, paper roll

; otherwise the

paper roll hold unit

may not open/close properly because of deformation or damage of the shaft.

Содержание EU-T532























































































































Результаты поиска

Содержание EU-T532

Отзывы:

Похожие инструкции для EU-T532

Бренды по названию

Популярные бренды

Epson EU-T532, Техническое руководство

Результаты поиска

Содержание EU-T532

Отзывы:

Похожие инструкции для EU-T532

Бренды по названию

Популярные бренды