Epson EU-T532 Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 118

background image

Rev. A

Maintenance 4-3

EU-T532/T542 Technical Manual

Confidential

Inspection

The maintenance and inspection procedures for the printer fall into two categories. One is
“Daily checks” for the printer user, and the other is “Periodic checks” for someone with more
technical knowledge. Maintenance and inspection procedures should be carried out by properly
qualified personnel.

Daily Checks

Make sure the printer is used properly and kept in good repair. If there are any problems,
replace the printer. The check items are as follows:

Periodic Checks

Every six months, check the items listed in the table below. If there are any problems, correct
them using procedures in the table blow.

Table 4-1 Daily Checks

Check item

Standard

Procedure

Setup status

No cables or connectors are
disconnected.

Connect the cables or connectors
properly.

Paper roll is loaded properly.

Load the paper properly.

No unit of each modules is open.
(the paper roll hold unit, the platen unit,
the upper frame, cut sheet presenter unit,
the cover, circuit board B, and etc.)

Close the units.

Paper chips or foreign
matter inside the
product

No paper chips or foreign matter is inside
the product

Remove paper chips or foreign matter.

Paper state

Specified paper is used.

Replace with the specified paper

No discolored or torn paper is used.

Replace with a new paper roll.

Table 4-2 Periodic Checks

Check item

Standard

Procedure

Dust, fuzz or dirt sticking
to various parts

•

No dirt or dust is attached or collected in

the paper path.

•

Remove dust, fuzz, or dirt with a vaccum

cleaner.

•

No paper chips or foreign matter

   is in the areas such as around the
   thermal head heating elements, the
   cutter, gears, detectors, and inside the
   paper path.

•

Wipe off dirt and dust with alcohol.

•

Remove foreign matter or paper chips.

•

Wipe off paper chips on the platen

surface with alcohol when the surface is
accumulated with paper chips.

Lubrication status

Lubrication is satisfactory.

Lubricate the lubrication points if
required.

Operating status

•

Printing, paper feeding and issuing

operations perform properly.

•

No abnormal sound

•

All other functions perform properly and

parts are not deformed or worn.

See “Troubleshooting” on page 5-2.

«
...
50
51
52
53
54
...
»

Содержание EU-T532























































































































Отзывы:

Нет отзывов

Похожие инструкции для EU-T532

Бренд: TallyGenicom Страницы: 2

Бренд: Xante Страницы: 25

Бренд: Zmorph Страницы: 16

Бренд: BIXOLON Страницы: 59

Бренд: Tektronix Страницы: 42

Бренд: 3DBNZ Страницы: 32

Бренд: Tally Страницы: 106

INFOPRINT HI-LITE COLOR 4005-HC2

Бренд: IBM Страницы: 10

DocuPrint C2535 A

Бренд: Xerox Страницы: 120

Бренд: Oki Страницы: 246

Бренд: Ouring Страницы: 54

Бренд: Ultimaker Страницы: 9

Бренд: Konica Minolta Страницы: 12

Aficio SP 320 Series

Бренд: Ricoh Страницы: 272

ApeosPort C6550 I

Бренд: Xerox Страницы: 132

V105 - All-in-One Printer

Бренд: Dell Страницы: 68

P703w - Photo All-in-One Printer Color Inkjet

Бренд: Dell Страницы: 105

Бренд: Dell Страницы: 125

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды