Epson EU-T532 Скачать руководство пользователя страница 58

Страница: 58 / 118

Rev. A

Repair 5-3

EU-T532/T542 Technical Manual

Confidential

PAPER OUT LED
is flashing.

Self test standby
state

Self test is in the
standby state

Check if the self test
printing is completed.

Press paper feeding
SW on the control
circuit board to
complete the self
test when not
completed.

ERROR LED is
flashing.
(For the LED
flashing
patterns, see
“Error LED” on
page 3-12.)

Print head high
temperature
error

The head
temperature has
reached at 70

C or

more.

−

(When the head is
cooled down to
60

C or less, the unit

will recover
automatically.)

ERROR LED is
flashing
(For the LED
flashing
patterns, see
“Error LED” on
page 3-12.)

Platen open error

The platen is open.

Check if the platen is
not open.

Close the platen
when it is open.

Platen open is
not detected.

The platen open
detector is
damaged.

Check the platen open
detector function with
an oscilloscope.

Replace the
detector if it is
damaged.

Autocutter error

(1)Paper chips or

foreign matter is
inside the
autocutter and
has locked it.

Check whether paper
chips or foreign matter
is jammed inside the
autocutter.

After turning off the
power, remove
paper chips or
foreign matter; then
turn on the power.

(2)The internal

function of the
autocutter is
damaged.

Check the power
supply voltage.

Replace the
autocutter if the
power supply
voltage is normal.

Black mark
detection error

(1)No black mark is

printed.

Check if the paper is
printed with a black
mark.

Replace with the
black mark printed
paper.

(2)The wrong side

of the paper is
used.

Check if the correct
side of the paper is
used.

Replace with the
paper with the
black mark on the
correct side.

(3)The black mark

detector is
damaged.

Check the black mark
detector function with
an oscilloscope.

Replace the
detector if it is
damaged.

(4)Paper chips or

foreign matter is
jammed around
the black mark
detector.

Check whether paper
chips or foreign matter
is jammed around the
black mark detector.

Remove the paper
chips or foreign
matter if there is
any.

Table 5-1 Troubleshooting

Phenomenon

Condition

Cause

Level

Where/how to check

Procedure

Содержание EU-T532























































































































Результаты поиска

Содержание EU-T532

Отзывы:

Похожие инструкции для EU-T532

Бренды по названию

Популярные бренды

Epson EU-T532, Техническое руководство

Результаты поиска

Содержание EU-T532

Отзывы:

Похожие инструкции для EU-T532

Бренды по названию

Популярные бренды