Epson ActionPrinter 4500 Скачать руководство пользователя

Страница: 242 / 317

Printer Specifications

Copy capacity:

Up to 3 sheets including the original. Total

thickness must not exceed 0.01 inches

(0.25

mm).

Note: Label printing and the printing of 24 lb paper are available
only at normal temperature and normal humidity.

Mechanical

Paper feeding methods:

Friction
Push tractor

Cut sheet feeder (optional)
Pull tractor (optional)

Ribbon:

Cartridge ribbon, available in black:
#7754

#7770 (film)

Life expectancy
of ribbon:

#7754: 2,000,000 characters
(in Letter Quality characters,
at 48 dots/character)

#7770: 200,000 characters
(in Letter Quality characters,
at 48 dots/character)

MCBF:

For all components excluding print head:

3,000,000

lines

MTBF:

6000

power on hours (duty

25 %)

Print head life:

200,000,000 strokes/wire

Dimensions and weight:

(excluding knobs and paper guides)

Height:

5.69 inches (144.5 mm)

Width:

23.35 inches (593.0 mm)

Depth:

13.66 inches (347.5 mm)

Weight:

18 lbs (8 kg approx.)

8-6

Technical Specifications

Содержание ActionPrinter 4500






























































































































































































































































































































Результаты поиска

Содержание ActionPrinter 4500

Отзывы:

Похожие инструкции для ActionPrinter 4500

Бренды по названию

Популярные бренды

Epson ActionPrinter 4500, Руководство пользователя

Результаты поиска

Содержание ActionPrinter 4500

Отзывы:

Похожие инструкции для ActionPrinter 4500

Бренды по названию

Популярные бренды