Epson ActionPrinter 4500 страница 233 Скачать руководство пользователя

Страница: 233 / 317

Options

Problem

Solution

Using the pull tractor

with the push tractor,

continuous paper does
not feed properly

(continued).

Skip over perforation
is set, but the skip has
shifted from the
perforation, or the
perforation does not
fall in the center of the
skip (continued).

When the printing
ends the paper feeds
abruptly, and as it
resumes printing, the
paper feeds backward
and comes off the pull

tractor sprockets.

When the

LOAD/EJECT

button is pressed to
eject the paper, the
paper comes off the
pull tractor sprockets.

The page length for one page of the
continuous paper may be set incorrectly.

Set DIP switch 2-1 or use your application
program control codes to set the correct
page length.

The short tear-off function may be selected.
The short tear-off function cannot be used

with the pull tractor, so be sure to set DIP
switch 2-2 to off. See Chapter 3.

When the paper release lever is in the

continuous paper position, the paper feeds
backward to eject. When using the pull

tractor, press the

FORM FEED

button to feed

the paper forward to eject.

Troubleshooting

7-31

Содержание ActionPrinter 4500






























































































































































































































































































































Результаты поиска

Содержание ActionPrinter 4500

Отзывы:

Похожие инструкции для ActionPrinter 4500

Бренды по названию

Популярные бренды

Epson ActionPrinter 4500, Руководство пользователя

Результаты поиска

Содержание ActionPrinter 4500

Отзывы:

Похожие инструкции для ActionPrinter 4500

Бренды по названию

Популярные бренды