Epson ActionPrinter 4500 страница 232 Скачать руководство пользователя

Страница: 232 / 317

Options

Problem

Solution

Using the pull tractor

with the push tractor,

continuous paper does
not feed properly

(continued).

Paper feed is crooked
or the paper jams
(continued).

Several lines of space
occur in the printout.

Skip over perforation
is set, but does not
work.

Skip over perforation
is set, but the skip has
shifted from the
perforation, or the
perforation does not
fall in the center of the
skip.

The paper may be slack. Adjust the
position of the sprockets to take up any

slack along the width of the paper. Remove
slack lengthwise by pressing in and rotating

the pull tractor knob on the right. Do not

turn the platen knob.

The paper thickness lever may not be

correctly set. Set the paper thickness lever
to match the thickness of your paper.

The paper may not meet the specifications.

Check that your paper is the proper size,
weight, and thickness.

Skip over perforation may be set. Set DIP

switch

2-3

to off.

You may have set the DIP switches with

the power on. To make new DIP switch
settings effective, turn the power off, then
on again.

The loading position of the paper may be

too high or too low. Use the micro-
adjustment feature to reset the loading
position.

7-30

Troubleshooting

Содержание ActionPrinter 4500






























































































































































































































































































































Результаты поиска

Содержание ActionPrinter 4500

Отзывы:

Похожие инструкции для ActionPrinter 4500

Бренды по названию

Популярные бренды

Epson ActionPrinter 4500, Руководство пользователя

Результаты поиска

Содержание ActionPrinter 4500

Отзывы:

Похожие инструкции для ActionPrinter 4500

Бренды по названию

Популярные бренды