Epson ActionPrinter 4500 Скачать руководство пользователя

Страница: 154 / 317

The Cut Sheet Feeder

Note:

If you turn off your printer during the time the printer

detects a paper out or paper

jam

condition, any data remaining

in the printer’s buffer is discarded.

Control panel operation

To operate the cut sheet feeder manually from the control panel when

the printer is in the cut sheet feeder mode, first make sure that the

printer is off line.

LINE FEED

When there is paper in the printer, press this
button to feed the paper one line or hold it down

to feed the paper continuously.

FORM FEED

When there is no paper in the printer, press this
button to load the paper. When there is paper in
the printer, press this button to eject the sheet.

LOAD/EJECT

When there is no paper in the printer, press this
button to load the paper. When there is paper in

the printer, press this button to eject the sheet.

Software operation

The following commands cause the printer to eject the sheet in the

printer without loading the next sheet.

FF:

Form Feed

ESC EM R:

Ejects a sheet in the cut sheet feeder mode

Note:

The ESC EM command is a software command used to control

the operation of the cut sheet feeder. For more information about this
command, see the Command Summary in Chapter

5-16

Using the Printer Options

Содержание ActionPrinter 4500






























































































































































































































































































































Результаты поиска

Содержание ActionPrinter 4500

Отзывы:

Похожие инструкции для ActionPrinter 4500

Бренды по названию

Популярные бренды

Epson ActionPrinter 4500, Руководство пользователя

Результаты поиска

Содержание ActionPrinter 4500

Отзывы:

Похожие инструкции для ActionPrinter 4500

Бренды по названию

Популярные бренды